Save 15% Off Body. Enter BODY15 Excludes body tubs & tub kits.

FREE SHIPPING on all orders $98+ See Details

Select Your Currency
Close
  • Africa
  • Americas
  • Asia
  • Europe
  • Oceania
Shop Kaiser Willys

Front Wheel Bearing Cone (inner & outer)
Fits 60-71 Jeep & Willys with Dana 27 front

Part # 925446

New Front Wheel Bearing Cone (4 required per vehicle)

Proper inner & outer bearing cone for your front hub. Requires (2) per side of vehicle. For bearings stamped: "LM501349"

Application:
Dana 27 front

Fits:
60-64 CJ-3B
60-71 CJ-5
60-66 M38A1
60-64 Truck
60-64 Station Wagon
66-71 Jeepster Commando (C101)

Part # Price
925446

$15.99

MSRP:

$15.99

MSRP:

1 Item has been added to your cart!
Close

Questions & Answers

Please Wait...

Ask Question Add Answer

All questions will be displayed after moderation. All answers will be displayed after moderation.

I have a 1964 J200 Gladiator Thriftside 4WD (Vin # 2406W11132). I am not sure if the front axle is a Dana 27 or a 44. Do these bearings fit? Best Regards Bernd

Willys Jeep Parts Tech:
You'll want to double check it to be sure. Email mike@Kaiserwillys.com to help.

I have a 1972 Jeep CJ5 with what I thought a Dana 30. I have a bade wheel bearing on the passenger side. However after taking off the locking hub on the passenger side I am not sure how to continue as there is no snap ring that I can see. It appears there is some type of retainer/seal in front of the nut but I can't get it to budge. This object has 5 small holes in what appears to be the outer ring, one if which is bigger than the other 4. It also has a slot that a screwdriver can fit in in the inner ring. I am unsure how to proceed. In all my internet research I have yet to find an item that even bears a resemblance to this item in front of the nut. Any insight would be greatly appreciated.

Willys Jeep Parts Tech:
Please email mike@kaiserwillys.com a picture of your set up and I can try to help out. Thanks!

i have a mixed parts cj5 FrankenJeep with mostly late 1950's-early 1960's chassis features. I'm not sure if the front axle is a 25 or a 27. It has the Bendix type joints and 9" brakes, but 6 bolt drive flanges and no snap rings to retain the end of the axle shaft. How can I tell which wheel bearings and hub seals are needed? Apparently the ID is the same where it fits the spindle, but I assume the OD differs to fit in the hub. Can you tel me the diameter of each so I can measure?

Willys Jeep Parts Tech:
If its 50's and early 60's I would assume its a Dana 25. If your bearings are stamped 'LM' then its the Dana 27.

I have a 1967 CJ5 jeep I am rebuilding the front axle. My question is I am putting new wheel bearings in and I need to know if you have to pack the wheel bearings with wheel bearing grease or are they oiled by the axle oil that is in the rear end. Thank You

Willys Tech:
You always need to properly hand pack your wheel bearings with heavy duty axle grease prior to install.
Request Catalog
X
THANK YOU! Your catalog request has been submitted successfully. Please note:

If your catalog does not arrive within 7-10 business days, call us Toll-Free at (888) 648-4923.

Email Subscription
X
THANK YOU! You have successfully subscribed to our newsletter.
Contact Form
X
THANK YOU! Your contact form request has been submitted successfully.
Photo Contest
X
SUCCESS! Your photo contest entry has been submitted!
Browser warning
The browser you are using to visit our website is no longer supported. For the best browsing experience, please visit us using a different browser.
I understand, close this message