Questions & Answers
Questions: Do the ujoints in these have zerks for grease?
Question By: Hank on Aug 5 2018 1:39 PM
Yes, they do. But they are pregreased from the factory.
Answer By: Willys Jeep Parts Tech on Aug 6 2018 5:42 AM
Questions: What is the length of this shaft?
Question By: Ivan on Feb 18 2018 9:45 PM
Overall length 35"
Answer By: Willys Jeep Parts Tech on Feb 19 2018 10:27 AM
Questions: Is this a 10 spline axle and will it fit a 47' CJ2A?
Question By: Stan Lee on Mar 11 2017 12:57 AM
Yes, this is a 10 spline and is for all the Willys Jeep's listed above.
Answer By: Willys Jeep Parts Tech on Mar 13 2017 5:53 AM
Questions: I still haven't found a definite on what is supposed to be in the Knuckles. As you put it I should fill it up to the fill plug, which is difficult with grease but that is what was in it. Can you tell me is it grease or oil in the knuckle? I am thinking it must be grease, the book says universal joint lube. Just seems funny to fill to a fill hole with grease. How do you know when you have it full? With oil it would run out the fill hole, with grease you could have it pumped all the way through the axle before it came out the fill hole? Thanks again for all your support, there are a lot of places to buy parts and I don't buy from you because you are the cheapest, I do it for the service and technical help. Thank you.
Question By: Elvis Hood on Nov 4 2016 8:06 PM
We typically use 90 weight gear oil.
Answer By: Willys Jeep Parts Tech on Nov 7 2016 5:34 AM
We use 90 weight non-synthetic.
Answer By: Admin on Apr 1 2017 1:03 AM
We typically use 90 weight non-synthetic. Fill till it comes out the fill hole on the side and re-plug. Thanks!
Answer By: Admin on Apr 18 2017 12:52 PM
Please give us a call toll free and we can go over it with you. 888.648.4923. Thanks!
Answer By: Admin on May 2 2017 8:58 PM
Questions: My new Universal joint axles came in today for my CJ2A thanks. Still struggling with lubrication and support. Am I to believe there is only support at the bushing in the spindle? Also how does this bushing get lubricated. I seen others ask this question and responses that the knuckle is still filled with Oil. Do you mean grease? and what would keep it from coming out the front of the spindle? I realize this is a lot to answer, but this is a huge investment to have something go wrong.
Question By: Elvis Hood on Nov 3 2016 5:42 PM
There is just the spindle bushing. Then your drive flange on the end of the hub has splines. It is a pre-lubed joint but you will still want to put knuckle lube in the knuckles up to the fill plug.
Answer By: WIllys Jeep Parts Tech on Nov 3 2016 11:01 AM
Yes, there is a spindle bushing and then you have the drive flange at the end. See diagram: https://www.kaiserwillys.com/diagram/cj-2a-diagrams/axle-diagrams-willys-cj-2a/dana-25-27-front-axle/dana-25-27-front-axle We use 90 weight non-synthetic.
Answer By: Admin on Apr 18 2017 2:14 PM
We typically fill with 90 weight gear oil. You will want to do this. That spindle bushing is the only support per se.
Answer By: Admin on May 2 2017 8:13 PM
Questions: I recently purchased a 1946 CJ 2-A that is mostly complete and original. I pulled the front diff cover and found that right and left axles, gear case and crown gear are all missing. The pinion is there but that's about it. Do you have good used gear cases and both axles? Will also likely need a crown & pinion as well just need to figure out the ration in the rear diff so it matches. Great site and lots of helpful information - thanks!
Question By: Bryan Nilsson on May 3 2014 12:00 AM
We can get you the carrier, spider gears, ring & pinion ect no problem. Please call us toll free.
Answer By: Willys Tech on May 5 2014 12:00 AM
We can help out with a lot of this. Please call us toll free and we can go over.
Answer By: Admin on Apr 6 2017 8:53 PM
Please give us a call toll free and we can go over it. 888-6484923. Thanks!
Answer By: Admin on Apr 23 2017 8:18 AM
Questions: With the new style can one replace just the spicer joint if needed at a later date or does it require a complete unit? I have the rezeppea style now and when pulled shaft out and bent completely down a ball fell out and i was able to put it back in does this indicate a badly worn joint. It seems to work ok after replacing ball.
Question By: d greenWith on Oct 5 2013 12:00 AM
You can do just one side if you want. We also sell the rezeppea style as well.
Answer By: Willys Tech on Oct 7 2013 12:00 AM
You can replace the joints as needed. Give us a call toll free and we can get you set up.
Answer By: Admin on Apr 12 2017 11:14 PM
Yes, you could replace the joint at a later time with the 909459 & 909460 if needed.
Answer By: Admin on Apr 28 2017 12:29 PM
Questions: With this joints do you still have to fill the knuckle with oil?
Question By: Anonymous on Nov 15 2012 12:00 AM
Yes, I do recommend it.
Answer By: Willys Tech on Nov 19 2012 12:00 AM
Yes, we use 90 weight.
Answer By: Admin on Apr 7 2017 6:20 AM
Questions: Just woundering if I can replace one axle. the new ones have the universal joint type pivit, while the old existing one that I won't change out will still have the older type joint. My jeep is a 1953 cj-3b. Thanks Jim
Question By: Jim on Aug 20 2011 12:00 AM
Yes you can replace just one side no problem.
Answer By: Willys Tech on Aug 22 2011 12:00 AM
We have customers that do it all the time. We recommend running the same in each side.
Answer By: Admin on Apr 13 2017 1:00 AM
Yes, we do have people replace just one. But I usually recommend doing it in pairs.
Answer By: Admin on Apr 28 2017 7:21 AM
Questions: I will need both driver and passenger side front axle shaft assemblies.
Question By: Floyd on Jan 1 1970 12:00 AM
The other part number is 909460. Yes, these come complete with fittings for grease.
Answer By: Willys Tech on Apr 18 2011 12:00 AM
909460 would be the part number for the passenger side.
Answer By: Admin on Apr 12 2017 11:05 PM
909459 is the driver side, like you see here. And 909460 is the passenger side: https://www.kaiserwillys.com/front-axle-shaft-assembly-for-passenger-side-rh-fits-41-71-cj-mb-gpw-m38-m38-a1-with-dana-25 Thanks!
Answer By: Admin on Apr 28 2017 12:59 AM
Questions: will this shaft directly replace the bendix type universal joint without any modifications
Question By: Anonymous on Feb 27 2011 12:00 AM
Yes, that is correct. They just slide in.
Answer By: Willys Tech on Feb 28 2011 12:00 AM
You may have to take a bit off of the bronze bushing at the end of your axle housing tube for clearance.
Answer By: Admin on Mar 31 2017 4:38 PM
You may have to take a bit off the bushing at the end of your axle housing tube for clearance on some models.
Answer By: Admin on Apr 18 2017 5:10 PM