Questions & Answers
Questions: My front seal must of had a small dust cover, not a large shield one like the rear. Mine looks more like the one in your video, however, I couldn’t get the smaller dust cover out of the old seal without destroying it. Is it of that much importance on the front Dana 25 differential?
Question By: Don on Aug 24 2019 12:59 AM
Please take an image of what you are referring to and email it to email@example.com. Typically there was just a hub oil seal there and an inner oil seal is all in the front.
Answer By: Willys Jeep Parts Tech on Aug 26 2019 5:38 AM
Questions: Is the dust cover required or can I remove the old one and just slide on the new seal?
Question By: Sean on Mar 6 2019 11:29 PM
If you have the style that has the shield I would put it back on.
Answer By: Willys Jeep Parts Tech on Mar 7 2019 5:50 AM
Questions: Is there supposed to be a "cover" on one side of the seal? The seals you sent me look the same on either side as per your first picture. They do not look like the one in the video.
Question By: Dennis Soltis on Jul 12 2018 12:05 AM
Your yoke has a dust shield. The spring side to the seal goes towards the differential.
Answer By: Willys Jeep Parts Tech on Jul 12 2018 5:58 AM
Questions: Is it possible to replace the pinion oil seal without having to reset the ring and pinion?
Question By: Steve on Mar 8 2018 3:13 PM
Yes, you should be able to slide off the yoke and replace. Its always a good idea to check your backlash when doing it though.
Answer By: Willys Jeep Parts Tech on Mar 8 2018 9:12 AM
Questions: Would you please tell me how find out what dana rear differential from a 1962 willys pickup , where to look at , and will this seal fit and what parts I will need to replace this seal . Thank you for your time ....
Question By: Farrell on Mar 15 2015 12:00 AM
If you have a Willys Truck 1962 then you would have a Dana 53 rear end. This is the proper one for you.
Answer By: Willys Tech on Mar 16 2015 12:00 AM
Questions: I have a '47 CJ2A with a Dana 41 Axle (Semi-Floating) and noticed in the Parts List manual it does not mention that I need this Pinion Shaft Oil Seal. Yet on this webpage it says it is for the Dana 41. I can not find this Pinion Shaft Oil Seal anywhere in the diagram. It just shows that I will need just a gasket, part No. 636565. Please help, thank you.
Question By: Jason on Jan 10 2015 12:00 AM
You definitely need a pinion shaft oil seal. This part number is required.
Answer By: Willys Tech on Jan 12 2015 12:00 AM
Questions: Are the front and rear pinion seals the same?
Question By: Rick on Nov 12 2013 12:00 AM
Yes that is correct. It fits all the applications above.
Answer By: Willys Tech on Nov 12 2013 12:00 AM
Questions: Will this seal work with a yoke that has the umbrella like shield.
Question By: Anonymous on Jul 17 2013 12:00 AM
Yes these are the proper pinion shaft oil seals for the original dust covers as well.
Answer By: Willys Tech on Jul 18 2013 12:00 AM
Questions: pinion shaft yoke is there a felt washer in there show picture of it
Question By: bob mettler on Jun 9 2013 12:00 AM
We sell the gasket part number: 636565
Answer By: Willys Tech on Jun 10 2013 12:00 AM
Questions: Is the other side raised or flush? I'm finding that there are 2 different seals witht he same item #.
Question By: Anonymous on Feb 11 2013 12:00 AM
It is flat. This is 100% the correct seal for the vehicles listed above.
Answer By: Willys Tech on Feb 11 2013 12:00 AM
Questions: Will this oil seal fit my 1960 FC 170?
Question By: Mike on Sep 25 2012 12:00 AM
Yes, it will be correct.
Answer By: Willys Tech on Sep 25 2012 12:00 AM
Questions: The side shown above does that side go in to the axle or out towards the yoke and driveshaft?
Question By: grant on Nov 13 2010 12:00 AM
The spring loaded side of the seal goes towards the ring & pinion.
Answer By: Willys Tech on Nov 15 2010 12:00 AM