Replacement Transmission Support Crossmember Fits 49-71 CJ-2A, 3A, 3B, 5, 6, M38, M38A1

Replacement Transmission Support Crossmember
Fits 49-71 CJ-2A, 3A, 3B, 5, 6, M38, M38A1

Part # 7372507

New Replacement Steel Transmission Support Crossmember

Quality reproduction center crossmember to cradle your T-90 transmission and Dana 18 transfer case.

Bolts to the bottom of the frame rail on each side.

Measurement:
29-5/8" - overall length

Fits:
49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
55-71 CJ-6
50-52 M38
52-66 M38A1

Note:
WILL WORK FOR EARLY 1946-47 CJ-2A BUT FRAME HAS TO BE DRILLED TO MOUNT.

Part #	Price
7372507	$144.99 MSRP:

$144.99

MSRP:

Product Videos

Questions & Answers

Will this crossmember (7372507) work on a 1967 with the dauntless v6 and a t86 transmission?

This is more set up for the earlier but i think it would as long as you halve the style transfer case mount that is round and not square.

Will this work with a T-14 transmission and Dana 18?

Willys Jeep Parts Tech:
We have no confirmation that it would.

Hello, will this fit a 67 Jeepster commando with TH400?

Willys Jeep Parts Tech:
No, it will not.

DO YOU HAVE THE BUSHING THAT FITS THIS CROSSMEMBER (PART # 7372507)

Willys Jeep Parts Tech:
926671K

Do you have a cross member for a 1961 Willys Wagon with a T-90 transmission and a Dana 18 transfer case?

Willys Jeep Parts Tech:
We can help you with good used.

Are there replacement bolts that attach the cross-member to the frame?

Willys Jeep Parts Tech:
Those are a local hardware store item.

it is indicated that the cross-member fits a CJ-6, but only up to 71. Was something different in 1972? That is my year, and this looks "almost" identical. Any help would be appreciated. Thanks.

Willys Jeep Parts Tech:
We have not fit this up past 1971 but they probably would work thru 1975.

Does the replacement transmission crossmember need welded on?

Willys Jeep Parts Tech:
You could weld them on. I do believe originally they were bolted / riveted.

I need a transmission crossmember for a 1979 CJ5 , will this one work?

Willys Jeep Parts Tech:
Sorry, i dont have a good listing for that item.

I have a cj2a and I do understand this will work on my D18 transfer case. Question is with the overdrive in gauged does the 4 wheel drive still work?

Willys Jeep Parts Tech:
In 4WD you wouldnt use the overdrive because you have to be in low range with in 4x4 mode.

Do you have the early CJ2A cross member? I have an early CJ2A with an MB frame so the the crossmember mounts are just like the MB ones so the crossmember should bolt to the sides of the mounts and to the bottom of the frame.

Willys Jeep Parts Tech:
This crossmember - A5127 - is for the MB, GPW. Take a look at it and see if this is what you're looking for. Thanks

Will this fit 64 sw

Willys Jeep Parts Tech:
No, this is only for the CJ's. Give us a call toll free at 888.648.4923 and we can fix you up. Thanks

I need one for a 75 CJ5 Will this work? If no, where can I find one?

Willys Jeep Parts Tech:
This is different. Email mike@kaiserwillys.com and we can give you some salvage yard numbers.

Why is this crossmember so different compared to the original in a 46 CJ2A, do I need to remove the brackets on both sides of the frame to install?

Willys Tech:
Early CJ-2A's used a little different attachment to the frame. This one will work just fine it just needs to be drilled.

Do you have this part for a 1952 Truck

Willys Tech:
That is available good used only. Please call us toll free.

im looking for a diagram for a dana transfer case single shift

Willys Tech:
Please check out our shop by diagram section. We have a D18 transfercase diagram there. Its dual stick but they are basically the same.

Will this fit a 45 gpw and does it sit lower. I have a t90 in my gpw and the floor has been cut to make it fit. I am trying to avoid cutting when I replace the floor. If not what are my options.

Willys Tech:
If you have a T90 then you should be ok. You will have to drill it out though....

Do you have a price for a used crossmember for the M38A1 and an part # when I place an order? Kevin

Willys Tech:
We can get you a few different numbers for salvage yards. Please call us toll free.

By relocating the frame brackets this crossmember attaches to will this crossmember work for a military jeep that has had the T-84 transmission replaced with a T-90? Thank you.

Willys Tech:
Yes that is corect Im sure it can be used. But if you have a MB I would still use part number: A5127.

Do you have a transmission cross member for a 1953 Willys truck 4x4. New or used?

Willys Tech:
We can get it good used for the Willys Truck. Please call us toll free.

I have a 1943 Willys MB with a T-90 transmission. Should I used this Replacement Transmission Support Crossmember or should I use another one designed for my jeep?

Willys Tech:
That is an unoriginal transmission. I would go with this one and you may have to modify.

I'm looking for the transmission mounting bolts with rubber cushions(?) that go with the transmission support crossmember for a 1960 CJ5. Do you have these?

Willys Tech:
I beleive you mean the transmission mount. Its part number: A6156

Will this cross member work for 1950 station wagon?

Willys Tech:
No, but we can get you good used. Please call us toll free.

Will this fit 1955-71 CJ5?

Willys Tech:
Yes, this will work for your CJ-5. Thanks