Questions & Answers
Do you sell the LED flasher that is required?
Willys Jeep Parts Tech:
Your local Napa will have that. Thanks! You just need an electronic flasher.
Your local Napa will have that. Thanks! You just need an electronic flasher.
I have these Led taillights. I have a 1969 CJ 5. The existing wiring has 2 wires (hot and ground), the Leds have 3 (ground, power and turn signals). I hooked the power to the 2 Led wires (power and turn signal) and the ground to the ground. When I turn on the lights, only the Led lights come on, no brake, turn signal or flasher. work. Am I doing something wrong????
Willys Jeep Parts Tech:
Email mike@kaiserwillys.com and we can send over wiring instructions. I would also check your brake light switch.
Email mike@kaiserwillys.com and we can send over wiring instructions. I would also check your brake light switch.
I see these LED Lights have 3 wires, the taillights I have on my 1969 CJ5 have only 2 wires. (ground & power) Do I combine the black and red wires together and splice that to the one "power" wire I have?
Willys Jeep Parts Tech:
You have power, ground, turn signals.
You have power, ground, turn signals.
Can you give the size of these LED tail and stop light 12403.84. Is it 3 or 4 inch diameter?
Willys Jeep Parts Tech:
3-3/4"
3-3/4"
Do I need to change my flasher and flasher plug for LED's. I have the original lights in front. I can't get right side turn signals to work. I've checked everything I can think of to check. So I was wondering if I need a speciai flasher?
Willys Jeep Parts Tech:
If going to LED you do need a LED flasher for turn signals to work.
If going to LED you do need a LED flasher for turn signals to work.
Can you use these with a 6 volt systems?
Willys Jeep Parts Tech:
These are 12 volt only.
These are 12 volt only.
Where does the ground wire supposed to be attached to?
Willys Jeep Parts Tech:
Any good clean metal surface that is grounded.
Any good clean metal surface that is grounded.
What modifications to fit my 63 pickup on the LED tail lights Item # 12403.84
Willys Jeep Parts Tech:
They will mount right up. You just need to be 12 volts.
They will mount right up. You just need to be 12 volts.
I am looking for these for a 55 Wagon, does this replace the side brake lights? or does this go on the tailgate...
Willys Jeep Parts Tech:
You could mount them just about anywhere on the back.
You could mount them just about anywhere on the back.
Can these LED lights be wired for both directional and brake lights at the same time or would I need 2 sets to accomplish both?
Willys Jeep Parts Tech:
Yes, you should be able to wire them up to your turn signal switch if you have one on your column.
Yes, you should be able to wire them up to your turn signal switch if you have one on your column.
pls send shipping cost item 12403.84
Willys Jeep Parts Tech:
Please email mike@kaiserwillys.com your full shipping address and i can quote you out. Thanks!
Please email mike@kaiserwillys.com your full shipping address and i can quote you out. Thanks!
Will these lights work on my 1942 Willys MB Jeep?
Willys Jeep Parts Tech:
If you are 12 volt. They can mount just about anywhere.
If you are 12 volt. They can mount just about anywhere.
It says will fit MB/GPW with Modification. What modifications will be required for proper fit?
Willys Tech:
It mounts on two studs. You would have to fit it into the area where the old tail lights go.
It mounts on two studs. You would have to fit it into the area where the old tail lights go.
Will his work wih a 1952 M38A1?
Willys Tech:
Yes as long as you are 12 volt.
Yes as long as you are 12 volt.
YOU MIGHT ALSO BE INTERESTED IN
