Questions & Answers
Questions: Does kit t90bsg come with instructions
Question By: Stephen Brandly on May 4 2019 1:31 AM
It does not but if you do have any questions once you get the kit we can answer them for you at any time. Thanks
Answer By: Willys Jeep Parts Tech on May 6 2019 3:37 AM
Questions: on your minor overhaul kit for the T90... How much more would the cost be for the sealed bearings instead of the ones listed.. Thanks
Question By: Randy A. on Nov 10 2018 8:00 PM
We can include and discount. Please call us toll free. Happy to help out.
Answer By: Willys Jeep Parts Tech on Nov 12 2018 5:47 AM
Questions: Are the front and rear bearings sealed?
Question By: Terry Taylor on Nov 8 2018 6:31 PM
They were not originally but we now offer part numbers: 944559 & 943729
Answer By: Willys Jeep Parts Tech on Nov 8 2018 10:31 AM
Questions: What is the difference between the t90 transmission with the 1-134 engine and the t90 transmission with a 225 V6 engine?
Question By: Ray on Feb 14 2018 8:28 PM
Its a bit usually to have a T90 paired with the V6225 motor. Usually you see the T86AA with the V6225. If you do in fact have a very early CJ-5 with that T90 set up - really just the input shaft different between the two T90's..
Answer By: Willys Jeep Parts Tech on Feb 14 2018 12:46 PM
Questions: The synchronizer shift plates and springs are shown in your photo for P/N T90BSG transmission overhaul kit. There is a note next to the photo stating these parts are not included. I read some of the Q&A's associated with this kit and one of the answers said all parts shown in the photo are included. That is confusing. Are the synchronizer shift plates and springs included in this kit. If so, it would be less confusing if the note was deleted.
Question By: Steve McWhorter on Jul 10 2017 12:45 AM
This is for front spindle only. They didn't use this on the D44.
Answer By: Willys Jeep Parts Tech on Jul 10 2017 6:09 AM
Questions: I have a T90 column shift and I am looking for just the gasket for the top cover. Want to look inside before putting it back in service with a frame off restoration.
Question By: Elvis Hood on Oct 6 2016 11:13 PM
You will have to make some out of gasket sealant.
Answer By: WIllys Jeep Parts Tech on Oct 7 2016 5:47 AM
Questions: Are poppet springs and balls available?
Question By: Norman Paulu on Aug 29 2016 10:00 PM
642769 and 453593 are the part numbers your after. Thanks!
Answer By: Willys Jeep Parts Tech on Aug 30 2016 5:57 AM
Questions: On this t 90 kit, Item # T90BSG, will every thing be there as on the picture?
Question By: Klasie Breytenbach on Aug 21 2016 9:46 AM
Yes, the kit is as shown.
Answer By: Willys Jeep Parts Tech on Aug 22 2016 6:13 AM
Questions: my 52 m38a1 makes a moderate whine/grind when driving that goes away when clutch is depressed I was told by a mechanic friend that it's probably the throw out bearing.... Is that a possibility? And does this minor kit have that?.... Thanks
Question By: Dom on Mar 4 2015 12:00 AM
Your throw out bearing is in your clutch part number: 635529
Answer By: Willys Tech on Mar 4 2015 12:00 AM
Questions: Hi, I purchased a 61 cj5 with 2nd gear snycros out or so I was told. I rebuilt the trans and it worked fine for a few days except it would kick out of 2nd when decelerating then lost 2nd gear again. Upon taking off the top cover I saw that the top set of gears had moved back and would not allow the gears to mesh. I purchased syncro set and a few more parts to make sure everything stayed in place. But when finished even though shifter locks into 2nd the trans just grinds. Any ideas, thanks
Question By: David on Aug 16 2014 12:00 AM
It could be your 2nd speed gear itself as well. I would check it for wear as well.
Answer By: Willys Tech on Aug 18 2014 12:00 AM
Questions: I have a 63' that keeps popping out of first gear when going down steep hills in 4 low also I'm having troubles locking in the hubs, any ideas?
Question By: Mark on Jan 13 2014 12:00 AM
It is probably your poppet balls and springs. I would check those for wear.
Answer By: Willys Tech on Jan 13 2014 12:00 AM
Questions: My cj2a is a bit of a frankinstine is there a way to tell if I have the t90 or t84 transmission in it
Question By: George on May 5 2013 12:00 AM
It will be stamped right on the drivers side of the case.
Answer By: Willys Tech on May 6 2013 12:00 AM
Questions: I'm intending to overhaul the T90a1 and T18 in my CJ-3B. Can you tell me who made your overhaul kits. Can you tell me who manufactured the main bearings or where they were made (China, Japan, USA?). thanks for your time.
Question By: Carl on Jan 28 2013 12:00 AM
We have them done by our professional rebuilder. The bearings are US made.
Answer By: Willys Tech on Jan 28 2013 12:00 AM
Questions: I have a 1960 Willys Jeep Truck w/a 6-226 flathead in it. I am looking to overhaul the transmission and transfer case and am wondering if any shims are required on either one and if so do they come in the minor overhaul kit. I believe all the gears and shafts are in good shape but both need new seals and the transmission is making what sounds like front bearing noise. Thanks. MB
Question By: Marc on Mar 19 2012 12:00 AM
The only place there really are shims is on the rear output of the transfercase. This is a great kit that will take care of most of your problems.
Answer By: Willys Tech on Mar 20 2012 12:00 AM
Questions: I am getting a Jeep with a T90 3 speed in it, but the high and low gears do not work only the reverse does. Do I need a complete rebuild or is it something simple?
Question By: Sean on Feb 14 2012 12:00 AM
Sounds like it is your syncronizer. I would start there. We have them part number: 640391
Answer By: Willys Tech on Feb 15 2012 12:00 AM
Questions: what are the part #'s for the synchronizer shift plates?
Question By: Anonymous on Feb 3 2012 12:00 AM
Part number: 640395
Answer By: Willys Tech on Feb 6 2012 12:00 AM
Questions: Does this kit come with the brass blocking rings and the FWD and Aft felt shaft seals?
Question By: Joe on Jun 14 2011 12:00 AM
This is less brass blocking rings but does come with seals.
Answer By: Willys Tech on Jun 14 2011 12:00 AM
Questions: Does this kit T90BSG (Minor overhaul kit)come with synchronizes?
Question By: Bill on Mar 23 2011 12:00 AM
No, it does not come with syncro parts. Try part numbers: 640394, 640395 & 640397. If you want the complete syncro it is part number: 640391
Answer By: Willys Tech on Mar 23 2011 12:00 AM