Questions & Answers
Questions: I have early CJ2A with bell crank ball that bends down. If I buy the bell crank with ball that bends up and your new drag link, can I turn down this shaft to 3/4 in. dia. to fit into the old bell crank bracket welded on the frame? Will the new bell crank fit with the rest of the steering linkage up front(tie rod ends etc)?
Question By: Richard Horth on Sep 6 2019 1:49 AM
I think you will have to reweld the bracket and modify it to work. Ive not tried this personally.
Answer By: Willys Jeep Parts Tech on Sep 9 2019 6:19 AM
Questions: I have a 1961 CJ-5, this Kit works for my jeep?, and do you have shipments to Mexico?
Question By: Raul on May 7 2019 9:15 PM
Yes, this is the proper one. We ship daily UPS and USPS international.
Answer By: Willys Jeep Parts Tech on May 8 2019 6:09 AM
Questions: I have a willy jeep with the title saying it is a 1948 CJ3A serial number 61910. Which of the bellcrank repair kits will work on this jeep?
Question By: Bob Shelton on Dec 20 2018 8:33 PM
Yes, as long as you are the 7/8" shaft and the ball on you bellcrank bends up.
Answer By: Willys Jeep Parts Tech on Dec 21 2018 5:29 AM
Questions: I have an original 1959 CJ-6, 4 cylinder F engine. Will parts listed for CJ-5 in the 1959 date range, work for my vehicle?
Question By: Joey on Mar 24 2018 2:32 AM
Yes, this will be the correct kit for that application. Thanks
Answer By: Willys Jeep Parts Tech on Mar 25 2018 2:02 PM
Questions: I AM INSTALLING A BRAND NEW BELL CRANK. THERE ARE NO INTERNALS. IS THIS KIT COMPLETE. IS THERE A BUSHING WITH THIS KIT THAT I AM NOT SEEING?
Question By: JOHN on Jan 1 1970 12:00 AM
This is the complete bellcrank repair kit with bushings. This will be everything you need.
Answer By: Willys Tech on Aug 30 2013 12:00 AM
Questions: Does this Steering Bellcrank Repair kit (920556) come with the 2 1/4 pivot shaft clamping screw and nut
Question By: Ron Jones on Jul 22 2013 12:00 AM
It will have everything shown in the photo.
Answer By: Willys Tech on Jul 22 2013 12:00 AM
Questions: Does that shaft fit my cj2a 1946... Thank s, Luc
Question By: Anonymous on Jul 4 2013 12:00 AM
Yes as long as the ball on your steering bellcrank points up. If it points down then you need part number: 915762
Answer By: Willys Tech on Jul 8 2013 12:00 AM
Questions: I have a 1947 CJ-2A willys, does this bellcrank repair kit fit's my willys
Question By: Ed on Jun 2 2013 12:00 AM
Yes as long as you have a 7/8 shaft. They also used part number: 915762 that used a 3/4 shaft.
Answer By: Willys Tech on Jun 3 2013 12:00 AM
Questions: I have a 1960 cj3b. The last owner had jacked the jeep up and jury rigged a pillar to accommodate the job. I found a bell crank bracket, but it has a 3/4 shaft with a drift pin. Will this work on my vehicle, and which bell crank do I need if it is workable?
Question By: Ron Howell on Mar 30 2013 12:00 AM
The 3/4 shaft was only used on early 1941-46 MB, GPW, CJ-2A. You want a 7/8 shaft. Try part numbers: 647008 & 920556 will be correct for the CJ-3B.
Answer By: Willys Tech on Apr 1 2013 12:00 AM
Questions: I have a 197 Cj-5 jeep with a stock 134 engine. Without taking apart and measuring the bellcrank bolt ,will this kit fit my Jeep or do I nee the 1 1/8 kit?
Question By: Bob McKeag on Jan 1 1970 12:00 AM
You always want to measure if your in the 1970's. Typically after 1968 your are the later 1-1/8 and 1967 and prior you are the 7/8.
Answer By: Willys Tech on Feb 25 2013 12:00 AM
Questions: Dose the rubber dust seal come with part N. 920556? or have to order sepert for 7/8 bolt ? Thank you Bill
Question By: Bill on Jan 16 2013 12:00 AM
Yes it does come complete in the kit.
Answer By: Willys Tech on Jan 16 2013 12:00 AM
Questions: 1952 Jeep m38. Took apart bellcrank and I pulled out 2 dust seals and bearings out. Where does the bushing go then?
Question By: Nate Atkins on May 11 2016 12:49 AM
The dust seals go on the top and bottom of the bearings to keep debris out.
Answer By: Willys Tech on May 11 2016 6:06 AM