Questions & Answers
Questions: Regarding transmission mount, I have steel adapter plate, but it is still not matching up, the 4 holes are off by .25 to .5", any advice? Is it just a matter of trying to tweak/shift the trans a bit until holes match up? Thx
Question By: Chris on Feb 6 2019 4:26 AM
We will need to get more vehicle information from you. Please email firstname.lastname@example.org or call us toll free. Happy to help out.
Answer By: Willys Jeep Parts Tech on Feb 6 2019 6:02 AM
Questions: There's a bolt attached adjacent to the rectangle mount on the crossmember. It seems to secure a bracket to the frame that also has a tooth adjacent to the bolt hole. It seemed mine had a wire wrapped around and extending to the rear (of course cut off from destination). Is this some type of ground wire? It doesn't seem to be an add-on, because of the 2 holes in the crossmember.
Question By: Steve on Jan 6 2019 3:24 PM
Please email email@example.com an image of your set up and I can take a look for you. Thanks!
Answer By: Willys Jeep Parts Tech on Jan 7 2019 5:45 AM
Questions: Where do I get the rubber that sits in the original motor mounts on a Cj3b?
Question By: Stephen Johnson on Sep 26 2018 2:41 AM
638629 are the part number for the front motor mounts on a CJ-3B
Answer By: Willys Jeep Parts Tech on Sep 26 2018 9:25 AM
Questions: gotta dana 18 and one of the side mount ears is broke off the casing. what do you recommend?? cant really afford a whole new housing.
Question By: derek on Dec 15 2017 6:49 AM
You could try to JB weld it if its not too bad. But really getting a new housing is probably your only option.
Answer By: Willys Jeep Parts Tech on Dec 15 2017 5:43 AM
Questions: The transfer case label on my 47 CJ-2A identifies Spicer as the manufacturer and also as a Brown Lipe gearbox. Spicer serial # is J 121754 and it is stamped Model 18.Is this the same as the Dana? The transmission is stamped T80 - 148. Is the 638629K what I need?
Question By: Ed on May 21 2015 12:00 AM
Yes, that is the Spicer Dana 18 transfercase. Your transmission is a T-90. Yes, this will be the correct kit for your Willys.
Answer By: Willys Tech on May 21 2015 12:00 AM
Questions: I have a 1947 CJ2A, The engine that came in all the boxes,Is a F Head not the L head.What Problems will I have putting in the F Head Engine and not the L Head Engine??
Question By: Doug on Mar 11 2015 12:00 AM
You will have to cut a hole in your hood to accommodate the taller carburetor height.
Answer By: Willys Tech on Mar 12 2015 12:00 AM
Questions: I am having a hard time understanding how the transmission mount attaches to my t-90transmission. The studs on the mount are wider than the holes on the bottom of the transmission. Is there a part I'm missing?
Question By: Daryl on May 11 2013 12:00 AM
You are missing the steel adapter plate that was originally there. We can get you good used.
Answer By: Willys Tech on May 13 2013 12:00 AM
Questions: I'm replacing the transfer case rubber mounts on a 45 Willys and we have the old bolt out and the small lower rubber snubber off. But, the problem now is getting the old large, upper rubber snubber out. The transfer case is resting on the upper snubber. Is it possible to remove the old and install the new snubber with the transfer case resting on the upper mount? Or is there much more to it? Thanks
Question By: Anonymous on Jan 3 2013 12:00 AM
I would drop the transmission and transfercase down and unbolt it all together to install on the crossmemmber.
Answer By: Willys Tech on Jan 3 2013 12:00 AM
Questions: i need transmission mount and transfer case isolator only can i purchase those two item or do i have to get the motor mounts as well
Question By: randy hoagland on Jan 23 2012 12:00 AM
Sure they are part number: 638629 & 926671K
Answer By: Willys Tech on Jan 23 2012 12:00 AM