Save 10% Off Site Wide. Enter PADDY10 Exclusions apply

FREE SHIPPING on all orders $98+ See Details

Select Your Currency
Close
  • Africa
  • Americas
  • Asia
  • Europe
  • Oceania
Shop Kaiser Willys

Clutch Release Bellcrank Spring
Fits 41-71 Jeep & Willys

Part # A178

NNew Replacement Clutch Release Bellcrank Spring (2 required per vehicle)

Sits inside the clutch release bellcrank between inner cotter pin and metal disc to spring load felt against pivot studs.

Application
4-134 engine
6-226 engine
V6-225 engine

Fits:
41-45 MB
41-45 GPW
46-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
55-71 CJ-6
50-52 M38
52-66 M38A1
46-64 Truck
46-64 Station Wagon
48-51 Jeepster

Part # Price
A178

$3.99

MSRP:

$3.99

MSRP:

1 Item has been added to your cart!
Close

Product Videos

Questions & Answers

Please Wait...

Ask Question Add Answer

All questions will be displayed after moderation. All answers will be displayed after moderation.

Will this work in my cj6 special long of 54? If not, you have this emergency hand brake can and handle for this vehicle? Thanks

Willys Tech:
The CJ-5/6 used a T-handle set up. I dont think this will work for you. The T-handle ones are only available good used.

will this work with my cj3b 1961, and how about the cable to connect to the lever.

Willys Tech:
It will probabaly work but the ball may be a bit small on the 3B.

do you guys also sell the felt padding that sit on the pivot studs

Willys Tech:
A176 is the part number.

i own a 1965 cj5.. im looking for the hand brake with cable.. do you have it??

Willys Tech:
That is part number: 906750 We can get good used on the cane shaft.

I ordered two of these springs; however, I don't see anyway for two springs to fit into the clutch release bell crank. There's clearly enough room in one end of the shaft, but the cotter pin holes on the other end are too close to the end for the spring and the clutch stud to fit in. I also have an old repair manual that shows only 1 spring. Please advise how both springs are supposed to fit in.

Willys Tech:
The one spring is compressed pretty far so that everything is tight.

will this work on my 1961 cj5

Willys Tech:
CJ-5 originally used a T-handle syle end.

Will the emergency brake handle work on a 59 Willys pickup?

Willys Tech:
This is for M38A1 only. We can get you good used for your Willys Truck.

My E-brake cable has a ball end. Will this hand brake handle fit it?

Willys Tech:
Yes that is correct.

Do you have an emergency brake handle for the CJ2A or CJ3A?

Willys Tech:
Sure. Please call me toll free. Can you also try part number: A351

My 55 M38A1 has a ratcheting pull handle on the floor between the seats that pulls straight up. It appears original. Which one is correct? The linkage between the handle and emergency brake are gone and I can not make the vertical linkage/handle pull the horizontal brake effectively.

Willys Tech:
This is the correct one pictured.
Request Catalog
X
THANK YOU! Your catalog request has been submitted successfully. Please note:

If your catalog does not arrive within 7-10 business days, call us Toll-Free at (888) 648-4923.

Email Subscription
X
THANK YOU! You have successfully subscribed to our newsletter.
Contact Form
X
THANK YOU! Your contact form request has been submitted successfully.
Photo Contest
X
SUCCESS! Your photo contest entry has been submitted!
Browser warning
The browser you are using to visit our website is no longer supported. For the best browsing experience, please visit us using a different browser.
I understand, close this message