Questions & Answers
Questions: I currently have an old Painless wiring harness that includes their fuse block on my 1971 CJ5 with a 225 V6. The wiring throughout my project Jeep is in pretty rough shape. (Engine was not in it, dangling poor quality wires everywhere). If I go with this harness, how would I connect each circuit into the existing Painless fuse block?
Question By: Dennis on Dec 5 2021 9:17 PM
Fuse blocks are unoriginal. You would have to contact painless on how they have it set up.
Answer By: Willys Jeep Parts Tech on Dec 6 2021 6:01 AM
Questions: I have a 1967, CJ5, Dauntless 225 V6. I would like to install your wire harness however, it appears so original that there are no fuses. Painless and others have included a fuse block, but provide for items not on my jeep. Theirs is not original. Does your kit allow for or include a fuse block or fuses?
Question By: Mike Pierce on Jan 17 2021 8:02 PM
You would just wire in a fuse block inline.
Answer By: Willys Jeep Parts Tech on Jan 18 2021 6:10 AM
Questions: Pretty sure Im going to have to rewire an entire 1969 Jeep. Just trying to make sure this is what I'm looking for. Does this kit come with all of the connectors to hook up to and plug into things like alternator and the engine starter and coil?
Question By: Carter on Jun 6 2020 10:14 PM
These are complete wiring harnesses all pre terminated like factory original.
Answer By: Willys Jeep Parts Tech on Jun 8 2020 5:44 AM
Questions: I have a 71 cj5, with v6 225.. can not get the rear backup lights to come on.. I tested the switch on top of the trans.. seem to work. where does the hot wire come from.? how can i down load the wire instuctions..
Question By: rick shaw on Oct 18 2018 4:22 PM
Pretty sure its off the ignition but will have to confirm.
Answer By: Willys Jeep Parts Tech on Oct 18 2018 11:38 AM
Back up lights are powered in the run position. With the trans in reverse you should have a closed switch, zero ohms on a meter and infinite when not in reverse. If all you have is a test light than check for light on both sides of the switch when it is in reverse. Check your hayes manual to see if there is a fuse or relay in the circuit, i can not see a relay being there since the draw is so low. Hope this helps.
Answer By: Chrles David Sparks on Dec 30 2019 11:00 PM
Questions: Looking for a harness for a 1972 cj5 with a 304 v8. Do you have this available, I believe it was the first year of amc, but is still basically a Kaiser body....
Question By: Marc laderoute on Sep 13 2018 1:42 PM
Sorry, i dont have a good listing for this year.
Answer By: Willys Jeep Parts Tech on Sep 13 2018 11:09 AM
Questions: do these come with directions?
Question By: manny on Jan 31 2018 7:08 PM
Yes it does. Thanks
Answer By: Willys Jeep Parts Tech on Feb 1 2018 5:04 AM
Questions: Hello I am looking for a Wiring Harness for a 1965 CJ 6. Engine was changed out to the 225 Dauntless V6 3.7 back in 66'. Do you have this in stock?
Question By: Gilbert R. Perez on Feb 6 2017 9:51 PM
We custom make these and can help you. Please call us toll free and we can fix you up.
Answer By: Willys Jeep Parts Tech on Feb 7 2017 5:58 AM
Questions: I have a 1970 CJ5 with the 225 V6. Looking at the pictures for this harness, I see more than just wires. Are the switches (lights, etc) included as well with the kit? Also, does the kit come with a new fuse box? Please list all parts that come with this kit. Thanks.
Question By: Bryan on Sep 21 2014 12:00 AM
It will come with everything that is shown in the photo. Guages and senders are not included. They are complete 'wiring' harnesses. All factory preterminations will be there.
Answer By: Willys Tech on Sep 22 2014 12:00 AM
Questions: I am a 1944-46 jeep willys with the Dauntless 225. Will this wiring harness fit?
Question By: Adam on Jul 7 2013 12:00 AM
We custom make the harnesses. Please call us toll free. We can help you.
Answer By: Willys Tech on Jul 8 2013 12:00 AM
Questions: I have a 52 m38a1 with a Buick 198 v6 fireball Eng. i am converting to 12 volt and do not want to use the original waterproof wiring. would this harness work for me?
Question By: Brad Pollock on Feb 10 2013 12:00 AM
Yes that is correct. We custom make them so you would be all set.
Answer By: Willys Tech on Feb 11 2013 12:00 AM
Questions: I have a 1951 m38. It has a 225 dauntless, and drive train from a 1966 cj-5. The system has been converted to 12v. I need a harness to accomodate the changes. Is there anything y'all could do to help?
Question By: Craig Carroll on Aug 19 2012 12:00 AM
Yes we custom make harnesses and can get you fixed up. Please call us toll free.
Answer By: Willys Tech on Aug 20 2012 12:00 AM
Questions: I have a 69 J-2000 with the Buick 350. Do you have a wiring harness that will fit this truck?
Question By: Gary on Aug 9 2012 12:00 AM
You would have to have that harness made up locally.
Answer By: Willys Tech on Aug 10 2012 12:00 AM
Questions: Do you have a voltage regulator for a 1968 cj5 v6 225 dauntless all original it mounts on the passenger side inner fender it has about a three inch wire lead(red green gray wires)with a female plug
Question By: Thomas on Feb 2 2012 12:00 AM
Try part number: 923130
Answer By: Willys Tech on Feb 3 2012 12:00 AM
Questions: dose this kit come with step by step instructions.
Question By: Anonymous on Nov 4 2011 12:00 AM
Yes it shows wire for wire where everything goes.
Answer By: Willys Tech on Nov 4 2011 12:00 AM
Questions: I have a 1969 Kaiser CJ-5 which was converted to V6-225 engine, and keyed ignition on dash. I assume this fits ok? Does it come with a fuse block? Options available with kit?
Question By: Anonymous on Sep 1 2011 12:00 AM
Yes this will work great. I have a series of questions I have to ask to get it custom made. Please call us toll free.
Answer By: Willys Tech on Sep 6 2011 12:00 AM
Questions: MY CJ5 IS A 1960 BUT NOW HAS A DAUNTLESS 225 BUICK V6. WILL THIS KIT WORK FOR ME ?
Question By: Robert on May 29 2011 12:00 AM
Please call us toll free. I can go over your options. We custom make them.
Answer By: Willys Tech on May 31 2011 12:00 AM
Questions: Will this kit work with a 1971 Jeepster Commando?
Question By: Anonymous on Apr 11 2011 12:00 AM
No, but we have one that will. Please call us toll free.
Answer By: Willys Tech on Apr 11 2011 12:00 AM