Product Videos
Questions & Answers
Sort By:
Questions: What lubrication is used on the felt pads ???
Why 2 springs ??? I only show 1 used in the Z rod.
Thanks
Question By: Gerald Jacyno on Oct 9 2020 6:30 PM
We use heavy duty axle grease. Really it is only 1 spring. We usually try to get an extra on the other side for tighter tension on the linkage.
Answer By: Willys Jeep Parts Tech on Oct 12 2020 5:29 AM
Questions:
Where do I find clutch linkage clevis pins for 48 CJ2A?
Question By: Chin on Jun 23 2018 10:45 PM
Here a link to the clevis pin:
https://www.kaiserwillys.com/emergency-brake-clevis-pin-fits-46-66-cj-2a-3a-3b-5-m38
Thanks
Answer By: Willys Jeep Parts Tech on Jun 25 2018 5:21 AM
Questions: Would this kit fit my 68 CJ5 with the factory 225 v6? If not, do you have a kit for the v6s? Thanks
Question By: Nick on Dec 31 2017 9:59 PM
No, this kit is 4 cylinder only. Give us a call toll free and we can work a kit up for you. Thanks
Answer By: Willys Jeep Parts Tech on Dec 27 2017 1:28 PM
Questions: For a cj2a what is the correct order of the small clutch bell crank components? (springs, felt pads etc)
Question By: Jim on Jul 11 2017 9:17 PM
https://www.kaiserwillys.com/diagram/cj-2a-diagrams/clutch-diagrams-willys-cj-2a/clutch-control-41-71-willys-jeep/clutch-control-41-71-willys-jeep
Here is a link. spring, disc, felt, seal, stud.
Answer By: Willys Jeep Parts Tech on Jul 12 2017 6:34 AM
Questions: When I took my cluth bellcrank apart there was only one spring, no felt, disks or seals. My question is why is there two of everything in the kit I bought? do both sides need the felt, spring and disc? or just the long side? Thanks
Question By: Philip Steinert on Jan 24 2014 12:00 AM
Some take 2 springs some only take 1. We provide extra hardware. You for sure want to have the felt on both sides.
Answer By: Willys Tech on Jan 27 2014 12:00 AM
Questions: I have a 53 cj3b, do you use both springs on both ends of the bell crank it seems like there is room only on the one end, the cotter pin holes are not the same distance on both ends?
Question By: ken on Dec 26 2013 12:00 AM
On alot of vehicles only 1 spring is needed for tension.
Answer By: Willys Tech on Dec 26 2013 12:00 AM
Questions: Please inform me the long size clutch release cable in stock # 642624k-2 in kit # 7 because I need measure 10-1/4
Question By: Carlos on Jun 2 2013 12:00 AM
Yes that is correct.
Answer By: Willys Tech on Jun 3 2013 12:00 AM
Questions: I bought this kit. It has two loose pivot balls included - one is black anodized and the other is plated. Which is the inner and which is the outer?? Thanks, Jeff
Question By: Jeff on Mar 20 2013 12:00 AM
Part number: A181 is the inner & A179 is the outer (the one with the bracket).
Answer By: Willys Tech on Mar 20 2013 12:00 AM
Questions: I have a CJ-3a frame with a T-90c-148B (the markings on its side). When I put a new cross tube on the pivots don't line up. Should I be putting the engine in first , then aligning the cross tube. Also the clutch cable is very close to the trans, do I have the cross tube in the wrong way?
Question By: Joe on Mar 15 2013 12:00 AM
Sounds like you have it in the wrong way. I would take another look at it and adjust your clevis as well.
Answer By: Willys Tech on Mar 18 2013 12:00 AM
Questions: assembly order for control arm parts
Question By: garry on May 11 2012 12:00 AM
Working inside to out: cotter pin, spring, disc, felt, grease retainer, pivot.
Answer By: Willys Tech on May 14 2012 12:00 AM
Questions: what is the total length of the bellcrank?
Question By: Anonymous on Feb 3 2012 12:00 AM
They are 8 just like original.
Answer By: Willys Tech on Feb 6 2012 12:00 AM
Questions: Does this kit work with the t98 transmission?
Question By: Matthew Francisco on Apr 27 2016 1:42 AM
Sorry these really is only for the vehicles listed above.
Answer By: Willys Tech on Apr 27 2016 9:36 AM
You Might Also Be Interested In
Weekly Willys highlights and discounts sent to your inbox
