Questions & Answers
Questions: For the Rear seat, can two of these be used, or would it have to be a single across the lap belt setup that would have to be used?
Question By: DiggityKid on Apr 1 2020 7:37 PM
We typically do 2 of them in the rear. They fit nicely.
Answer By: Willys Jeep Parts Tech on Apr 1 2020 12:47 PM
Questions: Will these seat belts fit my front 2 seats in my 56 willys wagon.
Question By: Max on Feb 2 2017 5:52 PM
Yes I would order 2 of them for the front and 2 for the rear.
Answer By: Willys Jeep Parts Tech on Feb 2 2017 10:42 AM
Questions: I am purchasing a 54 Willys wagon. Will these belts work for the rear seat? Are there existing holes or am I drilling?
Question By: Phillip on Sep 21 2016 5:33 AM
This is the belt is would use. You will have to just drill the 2 mounting holes.
Answer By: Willys Jeep Parts Tech on Sep 21 2016 5:41 AM
Questions: I am rebuilding a 1965 Cj5, it didnt have any seats or seat belts when i got it. What seats should i use and would these seat belts work for it?
Question By: Jon on Mar 16 2014 12:00 AM
We can help you locate good used seat frames and the BELT-1, BELT-2, or BELT-3 are all good choices. Please call us toll free.
Answer By: Willys Tech on Mar 17 2014 12:00 AM
Questions: What is the width of the belts?
Question By: Anonymous on Oct 7 2013 12:00 AM
1-7/8 like most belts.
Answer By: Willys Tech on Oct 7 2013 12:00 AM
Questions: Can the be used for the rear seat for my 1969 CJ5 462 Jeep?
Question By: Chris on Feb 24 2013 12:00 AM
Yes, This is what I recommend for that.
Answer By: Willys Tech on Feb 25 2013 12:00 AM
Questions: What is the length on each of the pieces? I have a 1960 Willys pickup that does not appear to have ever had seat belts. I was hoping to mount these using the existing bolts that are for the seat frame. Thanks
Question By: Anonymous on Oct 13 2012 12:00 AM
I believe they are 60 and should work just fine for you.
Answer By: Willys Tech on Oct 15 2012 12:00 AM
Questions: HEY I HAVE A QUESTION MIKE, DO I NEED SEATBELTS IN MY 1957 WILLYS 1 TON PICKUP. IT DONT HAVE THEM NOW. I WOUL RATHER NOT PUT THEM IN IF I DONT NEED. THANKS
Question By: johny fitz on Mar 17 2012 12:00 AM
You will have to check with your local and state laws on that. Alot of times because of the age of the vehicle you may not have to.
Answer By: Willys Tech on Mar 19 2012 12:00 AM
Questions: have a 1995 jeep. driving and the clutch went to the floor. replaced the clutch master cyclinder still no clutch. any ideas thank you for your help
Question By: Anonymous on Jan 18 2012 12:00 AM
A 1955 Willys Jeep never used a clutch master cylinder so you have something unoriginal on there. Call us toll free. We can probably help you troubleshoot it.
Answer By: Willys Tech on Jan 18 2012 12:00 AM
Questions: Is there any reason these can't be used in the rear seat on my '69 CJ5? If not, do you have seat belts for the rear?
Question By: Erik on Nov 8 2011 12:00 AM
These will work just fine in the rear too.
Answer By: Willys Tech on Nov 8 2011 12:00 AM
Questions: I have a 1951 CJ-3A. I have received your non-retractable seat belts and am ready to install them. Where should I fasten them on the body for the driver and passenger seats? Also, do I need any other hardware to mount them to my Willy's? This is my first Willy's Jeep so wanted to make sure I do it right and that it is supported well. Thank you!
Question By: Erik on Jul 28 2011 12:00 AM
Place the mounts to the left and right of each seat in a spot that the washer is able to lay flat so it gets the maximum support from the floor board. All the hardware is included. Thanks again!
Answer By: Willys Tech on Jul 28 2011 12:00 AM
Questions: Do these mount to pre-existing holes or do they need to be drilled?
Question By: David on Mar 15 2011 12:00 AM
It depends on your vehicle. Some were predrilled some never had them. They work either way.
Answer By: Willys Tech on Mar 15 2011 12:00 AM
Questions: what length are the seat belts
Question By: terry on Jan 12 2011 12:00 AM
We will check.
Answer By: Willys Tech on Jan 12 2011 12:00 AM