Questions & Answers
Questions: I 'm having a time with this parking light socket that i purchased from you , trying to hold it in and push hard enough from back side thru hole and put 6 volt bulb in from front side it will not go far enough in hole so i can push light bulb in far enough for connection. Spring is working on socket any ideas? Broken these 6 volt bulbs in process! 1948 Willys CJ2A Thank you
Question By: Gilbert Cusworth on Apr 22 2022 1:32 AM
It is spring loaded for sure and will be under some tension to hold in place.
Answer By: Willys Jeep Parts Tech on Apr 22 2022 7:11 AM
Questions: How do you plug the wire into parking light socket??
Question By: Gilbert Cusworth on Apr 13 2022 10:29 PM
You have to solder them on. Thanks
Answer By: Willys Jeep Parts Tech on Apr 14 2022 12:12 PM
Questions: My grill was modified for different parking lights. What is the correct diameter for 641609?
Question By: Larry Lawrence on Feb 4 2020 3:26 AM
7/16" is diameter of hole it goes into.
Answer By: Willys Jeep Parts Tech on Feb 4 2020 9:29 AM
Questions: I have a '48 CJ2A, it was converted to 12 volt, I want to use parking lights as turn signals as well and get rid of the big fender lights that are on it currently. Will just changing the bulbs do it provided the wiring is run from the switch to the sockets?
Question By: Brian Peterson on Feb 16 2018 4:14 PM
As long as you have a dual lead and dual filament bulb it should function for turn signal.
Answer By: Willys Jeep Parts Tech on Feb 16 2018 11:31 AM
Questions: How do you wire this into the harness? Does this need to be soldered onto a wire? Is there a "plug" on the harness?
Question By: Steve Jackson on Apr 18 2017 1:42 AM
Yes, you run the wire thru the center and solder.
Answer By: Willys Jeep Parts Tech on Apr 18 2017 5:46 AM
Questions: the recessed whole in my 1947 grill is too large for part number 641609. what else do i need?
Question By: Anonymous on May 26 2015 12:00 AM
Sounds like you have the early style grill that takes the recessed parking light assembly that mounts behind the grille on the shelf just below the opening. Or someone drilled your hole out.
Answer By: Willys Tech on May 27 2015 12:00 AM
Questions: Does it only need this unit for a CJ 2a 1948 model? does it need a cup or anything else, I only have the grill and the lense and the bezel.
Question By: Donald Brink on Jun 27 2014 12:00 AM
This is required if you have protruding style parking lights. This just pops right into the dimple in the grille.
Answer By: Willys Tech on Jun 27 2014 12:00 AM
Questions: I have a 1946 CJ2A . the grill has a slight depression for flush mounting parking lights rather than recessed. What are the exact parts I would need to install new parking lights into this for both turn signal and parking lights?
Question By: Marcia on Apr 28 2013 12:00 AM
You have a small dimple. Part numbers: 641609, 641555 & 641556 would take care of it for you.
Answer By: Willys Tech on Apr 29 2013 12:00 AM
Questions: Does this include the little spring inside and the wire tip that together provide tension to the connector on the rear of the bulb? If not, where can the spring and tip be found?
Question By: Anonymous on Sep 24 2012 12:00 AM
Yes that is in there too.
Answer By: Willys Tech on Sep 24 2012 12:00 AM
Questions: what bulb does this take.
Question By: robert duncan on May 22 2012 12:00 AM
If you are running 12volts the proper bulb is part number: 131282
Answer By: Willys Tech on May 23 2012 12:00 AM