Save 15% Off Body. Enter BODY15 Excludes body tubs & tub kits.

FREE SHIPPING on all orders $98+ See Details

Select Your Currency
Close
  • Africa
  • Americas
  • Asia
  • Europe
  • Oceania
Shop Kaiser Willys

Front Axle Shaft Assembly for Passenger Side (RH)
Fits 41-71 MB, GPW, CJ-2A, 3A, 3B, 5, M38, M38A1 w/Dana 25

Part # 909460

New Front Axle Shaft Assembly for Passenger Side

Contains Both Long and Short Shaft with Universal Joint.

Application:
Dana 25 front

Measurements:
21-5/8"

Fits:
41-45 MB
41-45 GPW
46-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
50-52 M38
53-71 M38A1

NOTE:
If swapping from Bendix axle shafts, you must remove the bushing at the end of the tube (A6362 prior to installation for clearance. You will need to remove the knuckles and slide axle in from the back side.

Part # Price
909460

$185.99

MSRP:

$185.99

MSRP:

1 Item has been added to your cart!
Close

Product Videos

Questions & Answers

Please Wait...

Ask Question Add Answer

All questions will be displayed after moderation. All answers will be displayed after moderation.

When you send the front axles shaft there are two parts (seal?)- Diagram numbers 53 and 54- what is the P/N of it?

Willys Jeep Parts Tech:
Please give us a call and we can try to help you.

do you guys sell replacement universal joints for the axle shafts? I need one for the long shaft on my dana 27

Willys Jeep Parts Tech:
909476

I have a dana 27 for a 3B I'm rebuilding. I need replacement shafts for it. the shafts I pulled out are 10 spline. will this item work for the short shaft? and the long shaft you guys have for the dana 25, will it work for my 27?

Willys Jeep Parts Tech:
Yes that is right and 909459 for the other side.

Could I get the specs, diameter, length...?

Willys Jeep Parts Tech:
Please email mike@Kaiserwillys.com what all specs your wanting and we can help.

I have a 10 spline dana 25 right hand side. The inner axle shaft is 16 3/4” and the total length is 24 3/4”. Do you have something that would work for me?

Willys Jeep Parts Tech:
Please email mike@kaiserwillys.com some more vehicle information and we can help out. Thanks!

I need the weight of each front axle shaft, cause I need to buy from you, and then when it arrived to Miami I need to send the axles air way freight to South America, Uruguay, where is my CJ2A

Willys Jeep Parts Tech:
These weight approx 10 pounds boxed each.

I bought some used axles to replace the ones in my 46 Willys. The splines are the a same and they go into the side gears fine. I removed the axle tube bushings but neither would go in far enough for the spindle to bolt up. I cut about 1/2 inch off the inner left axle and that fixed that issue. The right side it seems the splines are not cut deep enough. Is there a different inner axle length that I can buy

Willys Jeep Parts Tech:
You may have a clearance issue there on the bushings at your housing or spindle. I would look at those. We do have NOS originals if you want to go that route too.

I noticed that the u joint type axles do not have a machined area for the outer axle bushing to ride on. When replacing the repezza with a joint type shaft is it necessary to remove that brass sleeve from the axle tube?

Willys Jeep Parts Tech:
If you are replacing the early style axles with these spicer style axle, you may have to take some off the bushing for clearance.

I ordered these but the u-joint/yoke won't slide through knuckle hole on my 48 cj2a. The u-joint part is too big. Your video shows them sliding through the knuckle hole. Do I need to remove the steering knuckle to install these?

Willys Jeep Parts Tech:
You could put in from backside if you slide it off. Send photos to Mike@kaiserwillys.com so we can take a look.

What size universal joints are in these axles shafts? I don't need the shafts just need to replace a universal joint.

Willys Jeep Parts Tech:
8126614S is the part number for them.

Are the rzeppa axleshafts for a dana 25 axle interchangeable with the spicer style axleshafts? In other words if I had an axle with one style could I replace them with the other style?

Willys Jeep Parts Tech:
If you can email mike@kaiserwillys.com more vehicle information and I can help out.

Does the outer flange fit up? I have this shaft but my outer flange fits very tight.

Willys Jeep Parts Tech:
Yes, your drive flange will slide onto the end of the shaft.

I will be replacing my Rzeppa style axles with the Spicer type that you offer and I have two questions. One how does one install lockout hubs when there is a snap ring at the end of the axle, and if you leave the snap ring off will the end play in the axle be OK? Two, I see that the Spicer joint is pre-greasable before it is assembled, but how can it be greased again when it is in a closed knuckle application? Thank you.

Willys Jeep Parts Tech:
To answer your first question, you would have to trim the threads off of the end of the rzeppa axle. For your second question, you grease the balls and inside the "cage" of the rzeppa shaft. But the knuckle is loaded with knuckle lube anyway and as the vehicle moves, it gets inside the joints.
Willys Tech:
Typically if you have the snap ring style axle shaft the length wont cause any problems. It just bolts up. The spicer style has a grease fitting that usually is just a one time grease.

when I removed the passenger side front axle from a 53 cj-3a the balls fell out of the joint. is this normal or is the joint worn out?

Willys Tech:
Sounds like you have worn balls on the joint. If you still have all the parts you could put them back together but they probably need to be replaced.

Switching to these Axle Shaft will that eliminate the need to grease inside the front hub?

Willys Tech:
You would still want to grease it just to make sure it is all lubricated but yes this is a spicer style joint that can be pregreased.

I understand these replace the RZeppa but I don't see the threaded end that the RZeppa has. Is/are there additional parts needed?

Willys Tech:
It comes with a snap ring to convert you over. Only really early ones were threaded.

Are all '46 CJ-2A front axles Dana 25's ? Seems to me that when I did the rebuild (14 years ago) that mine was a Spicer 21 with a Bendex joint. Am I correct or fuzzy in the brain ?

Willys Tech:
Yes all CJ-2A's or any 4wd Willys thru 65 were Dana 25. Starting the the 60's some CJ-5's had a Dana 27 option.

Does anything have to be changed or adjusted when replacing the bendix style with this?

Willys Tech:
Sometimes you have to take out the bushing at the end of your axle housing tube for clearance. Other than that you are all set to slide in.

what is the overall complete lenth also mine has a splined nut at the end past the 10 splines

Willys Tech:
21-5/8

Am I correct in assuming these axles and Ujoints replace the original Bendix axles with the ball type joint?

Willys Tech:
Yes that is correct. They are direct replacements.

Am I correct to assume these are 10 spline axles?

Willys Tech:
Yes, that is correct.
Request Catalog
X
THANK YOU! Your catalog request has been submitted successfully. Please note:

If your catalog does not arrive within 7-10 business days, call us Toll-Free at (888) 648-4923.

Email Subscription
X
THANK YOU! You have successfully subscribed to our newsletter.
Contact Form
X
THANK YOU! Your contact form request has been submitted successfully.
Photo Contest
X
SUCCESS! Your photo contest entry has been submitted!
Browser warning
The browser you are using to visit our website is no longer supported. For the best browsing experience, please visit us using a different browser.
I understand, close this message