FREE SHIPPING ON ONLINE ORDERS OVER $98.00 See Details

Steering Bellcrank (ball bends up)
Fits 48-71 CJ-2A, 3A, 3B, 5, M38, M38A1, FC-150, Jeepster Commando (7/8" & 1-1/8")

More Views

Steering Bellcrank (ball bends up)
Fits 48-71 CJ-2A, 3A, 3B, 5, M38, M38A1, FC-150, Jeepster Commando (7/8" & 1-1/8")

New Replacement Steering Bellcrank (1 required per vehicle)

Replace when your old ball is egg shaped or the bellcrank repair kit wont elimate all the slop due to a out of round center hole. Ball on bellcrank bends up.

This is the bell crank that fits all 7/8" and 1-1/18" bellcrank pins that were typically used on bellcrank 946965.

Fits:
48-49 CJ-2A after serial number 199079
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
50-52 M38
52-66 M38A1
57-64 FC-150
66-71 Jeepster Commando (C101)

Item # Price
647008
$79.99

Availability: In stock

Add to Wishlist

Product Videos

Questions & Answers

Sort By: 

  

Questions: I installed the (STEERING BELLCRANK REPAIR KIT (1-1/8" SHAFT) with this new bellcrak shaft and the and the new pin will not fit through the installed bearings. Do you have ay suggestions on how to get the pin through after the new bearing install? I am cautious to push too hard.
Question By: Travis Parrill on Aug 6 2022 6:25 PM
Should be a tight slip fit for sure. Email mike@kaiserwillys.com to help.
Answer By: Willys Jeep Parts Tech on Aug 8 2022 5:50 AM
Questions: Hi, is this part available?
Question By: Carlos on Jul 11 2022 6:29 PM
Yes, that is correct.
Answer By: Willys Jeep Parts Tech on Jul 11 2022 11:30 AM
Questions: How do i determine if i had an upward or downward facing bellcrank? The original had been removed from the frame, SN is 184xxx, but some of the other parts for this jeep have been pre 199xxx number.
Question By: Bill Casagranda on Feb 15 2022 2:36 AM
Look at your drag link. It will tell you which wall the ball when into it.
Answer By: Willys Jeep Parts Tech on Feb 15 2022 5:18 AM
Questions: My jeep needs a new bell crank and I have one, but it is the wrong style (points up instead of down). Can I convert from a pointing down bell crank to a pointing up by buying the appropriate bell crank repair kit and drag link?
Question By: David Richard on May 22 2020 11:48 PM
The main problem with that idea is that no one makes the early style drag link. They are only available good used. Give us a call toll free and we can get you set up. 888.648.4923. Thanks
Answer By: Willys Jeep Parts Tech on May 26 2020 3:22 AM
Questions: When I turned my wheels my steering connector rod gets suck on the radiator support beam , what could be the cuz our that .
Question By: Brandon on Oct 4 2019 11:28 PM
Sounds like your pitman arm or wheels may be out of alignment. I would check all your steering.
Answer By: Willys Jeep Parts Tech on Oct 7 2019 6:14 AM
Questions: The bellcrank on my '61 CJ-3b has a 7/8" brass bushing pressed into the steel center. I just bought a bell crank repair kit for you to remove "slop" from the unit. Do I need to drill or press out the brass bushing or replace the bell crank. If replacing, does 647008 have the right diameter to work with the repair kit (920556) I have?
Question By: Ellis Johnson on Apr 28 2019 2:05 PM
The bellcrank repair kit just requires your bellcrank. Any old bushings are not used.
Answer By: Willys Jeep Parts Tech on Apr 29 2019 6:01 AM
Questions: How does this part fit a 7/8" and a 1 1/8" shaft? Does it use a reducer bushing?
Question By: Greg Stein on Sep 14 2018 3:52 PM
Yes, there is a sleeve.
Answer By: Willys Jeep Parts Tech on Sep 14 2018 10:43 AM
Questions: Hello, i want to know how much it wheights if it is possible. Thanks, Alvaro.
Question By: Alvaro on Aug 10 2018 6:07 PM
6 pounds boxed
Answer By: Willys Jeep Parts Tech on Aug 10 2018 11:11 AM
Questions: I just installed new bell crank & repair kit and steering is very stiff, even with front wheels off the ground. Could I have overtightened something? Any suggestions? Thanks
Question By: jim on Jun 19 2018 12:56 PM
I would double check it by disconnecting the tie rods and drag link to confirm. You may want to check your king pins too and inside the gear box.
Answer By: Willys Jeep Parts Tech on Jun 19 2018 10:18 AM
Questions: How do you remove a steering connecting rod off the steering arm or the bel crank. My Jeep is a 1951 M38. Thank You. Dan.
Question By: Dan Sealy on Oct 24 2017 8:32 PM
You just unscrew either end cap on the drag link.
Answer By: Willys Jeep Parts Tech on Oct 25 2017 5:43 AM
Questions: It states this part fits through 71, but the repair kit says it is just up through 66. I need both, but will these 2 parts work on my 1970 CJ5?
Question By: Matthew Francisco on Aug 9 2016 8:17 PM
if your a 1970 CJ-5 your probably need part number: 991381. Measure yours and see which you need.
Answer By: Willys Jeep Parts Tech on Aug 10 2016 5:46 AM
Questions: To replace my bell crank on my '63 CJ3-B do I have to purchase the repair kit? or is the kit only if I want to attempt to fix my old one?
Question By: Jeff on Oct 24 2013 12:00 AM
Yes I would get both the bellcrank and the repair kit to fully do the job while you have it apart.
Answer By: Willys Tech on Oct 24 2013 12:00 AM
Questions: I believe I have a 48 cj2a I do I know for sure. I have a 3/4 bellcrank shaft I and when I install the bellcrank that bends up the shaft hits the frame and the one that bends down doesn't work for my shaft do I have the wrong shaft if so is I possible to cut off the end and turn it so it fits the one that bends down
Question By: Shawn on Jul 26 2013 12:00 AM
Please call us toll free, we can help you ID your vehicle and get you fixed up. If you are a 3/4 shaft then your bellcrank bends down and this is no the part for you. These are for 7/8 diameter shafts.
Answer By: Willys Tech on Jul 26 2013 12:00 AM
Questions: does this bellcrank 647008 use the 7/8s repair kit 920556
Question By: Anonymous on Jun 7 2013 12:00 AM
Yes that is correct. They are matching parts.
Answer By: Willys Tech on Jun 10 2013 12:00 AM
Questions: Need to find new or used CJ2A '46 bellcrank bending down. Can you direct me?
Question By: Anonymous on May 16 2013 12:00 AM
Please call us toll free. We can help you find a good used one.
Answer By: Willys Tech on May 17 2013 12:00 AM
Questions: can an early CJ2a with the ball turned down be converted to this style?
Question By: Bill on Apr 7 2013 12:00 AM
No, they are not interchangable.
Answer By: Willys Tech on Apr 8 2013 12:00 AM
Questions: Does it come with the brass bushing?
Question By: Micah on Feb 8 2013 12:00 AM
The bushings are part of the bellcrank repair kits that we sell.
Answer By: Willys Tech on Feb 11 2013 12:00 AM
Questions: I have a 54 Willy M38A1. The Bellcrank is very loose which means I need to repair the gears in the gear box since the bellcrank is very loose. However, I am unable to remove the Steering Wheel, thus the steering box to repair. Can this be accomplished while still in the jeep, or does this require enough space? I hope I asked this correctly.
Question By: Neil on Jan 31 2013 12:00 AM
You will really need to remove the steering wheel. Order part number: WP300 on our site. It will get you fixed up.
Answer By: Willys Tech on Jan 31 2013 12:00 AM
Questions: I need a bellcrank for a 1946 CJ2A ser# 24949
Question By: Jimmy on Apr 27 2012 12:00 AM
That is the style that the ball bends down on the steering bellcrank. We can probably get good used.
Answer By: Willys Tech on Apr 27 2012 12:00 AM
Questions: Will this part fit a 1969 jeepster commando?
Question By: Leon on Mar 23 2012 12:00 AM
Yes I believe it is correct.
Answer By: Willys Tech on Mar 23 2012 12:00 AM
Questions: I have a 46 Cj2a S/N 25459 with 3 on the tree. However the bell crank knob turns down. How can I order a good used one. is there a part number or listing?
Question By: Bob on Feb 13 2012 12:00 AM
Please call us toll free. We may be able to get you good used.
Answer By: Willys Tech on Feb 14 2012 12:00 AM
Questions: Do you have one of these that will fit an early 46 CJ2A (column shift model)?
Question By: Dana on Jan 20 2012 12:00 AM
The early CJ-2A with ball bending down are available good used right now.
Answer By: Willys Tech on Jan 23 2012 12:00 AM
Questions: I know this is probably a dumb question but will this work on a CJ2A before Ser#199079
Question By: Anonymous on Sep 5 2011 12:00 AM
As long as your ball bends up.
Answer By: Willys Tech on Sep 6 2011 12:00 AM
Questions: Does the steering bellcrank come with a bellcrank repair kit?
Question By: Anonymous on Jul 4 2011 12:00 AM
This is bellcrank only.
Answer By: Willys Tech on Jul 5 2011 12:00 AM
Questions: Have 1953 CJ3B, working on steering, purchased tierods, bellcrank...My Jeep has an item attached to the Bellcrank that I do not see in steering parts listings...Not sure if it is a later add on? Can I send a picture some where?
Question By: Dennis McGrath on Apr 4 2011 12:00 AM
Please call us toll free. We are more than happy to help.
Answer By: Willys Tech on Apr 5 2011 12:00 AM
Questions: will this fit my 1967 cj5a #647008
Question By: tom on Jan 28 2011 12:00 AM
Yes it is the correct one.
Answer By: Willys Tech on Jan 28 2011 12:00 AM