Questions & Answers
Questions: I have a willy jeep with the title saying it is a 1948 CJ3A serial number 61910. Which of the bellcrank repair kits will work on this jeep?
Question By: Bob Shelton on Dec 20 2018 8:33 PM
Yes, as long as you are the 7/8" shaft and the ball on you bellcrank bends up.
Answer By: Willys Jeep Parts Tech on Dec 21 2018 5:29 AM
Questions: I have an original 1959 CJ-6, 4 cylinder F engine. Will parts listed for CJ-5 in the 1959 date range, work for my vehicle?
Question By: Joey on Mar 24 2018 2:32 AM
Yes, this will be the correct kit for that application. Thanks
Answer By: Willys Jeep Parts Tech on Mar 25 2018 2:02 PM
Questions: I AM INSTALLING A BRAND NEW BELL CRANK. THERE ARE NO INTERNALS. IS THIS KIT COMPLETE. IS THERE A BUSHING WITH THIS KIT THAT I AM NOT SEEING?
Question By: JOHN on Jan 1 1970 12:00 AM
This is the complete bellcrank repair kit with bushings. This will be everything you need.
Answer By: Willys Tech on Aug 30 2013 12:00 AM
Questions: Does this Steering Bellcrank Repair kit (920556) come with the 2 1/4 pivot shaft clamping screw and nut
Question By: Ron Jones on Jul 22 2013 12:00 AM
It will have everything shown in the photo.
Answer By: Willys Tech on Jul 22 2013 12:00 AM
Questions: Does that shaft fit my cj2a 1946... Thank s, Luc
Question By: Anonymous on Jul 4 2013 12:00 AM
Yes as long as the ball on your steering bellcrank points up. If it points down then you need part number: 915762
Answer By: Willys Tech on Jul 8 2013 12:00 AM
Questions: I have a 1947 CJ-2A willys, does this bellcrank repair kit fit's my willys
Question By: Ed on Jun 2 2013 12:00 AM
Yes as long as you have a 7/8 shaft. They also used part number: 915762 that used a 3/4 shaft.
Answer By: Willys Tech on Jun 3 2013 12:00 AM
Questions: I have a 1960 cj3b. The last owner had jacked the jeep up and jury rigged a pillar to accommodate the job. I found a bell crank bracket, but it has a 3/4 shaft with a drift pin. Will this work on my vehicle, and which bell crank do I need if it is workable?
Question By: Ron Howell on Mar 30 2013 12:00 AM
The 3/4 shaft was only used on early 1941-46 MB, GPW, CJ-2A. You want a 7/8 shaft. Try part numbers: 647008 & 920556 will be correct for the CJ-3B.
Answer By: Willys Tech on Apr 1 2013 12:00 AM
Questions: I have a 197 Cj-5 jeep with a stock 134 engine. Without taking apart and measuring the bellcrank bolt ,will this kit fit my Jeep or do I nee the 1 1/8 kit?
Question By: Bob McKeag on Jan 1 1970 12:00 AM
You always want to measure if your in the 1970's. Typically after 1968 your are the later 1-1/8 and 1967 and prior you are the 7/8.
Answer By: Willys Tech on Feb 25 2013 12:00 AM
Questions: Dose the rubber dust seal come with part N. 920556? or have to order sepert for 7/8 bolt ? Thank you Bill
Question By: Bill on Jan 16 2013 12:00 AM
Yes it does come complete in the kit.
Answer By: Willys Tech on Jan 16 2013 12:00 AM
Questions: 1952 Jeep m38. Took apart bellcrank and I pulled out 2 dust seals and bearings out. Where does the bushing go then?
Question By: Nate Atkins on May 11 2016 12:49 AM
The dust seals go on the top and bottom of the bearings to keep debris out.
Answer By: Willys Tech on May 11 2016 6:06 AM