US Made Brake & Clutch Pedal Cross Shaft
Fits 48-71 CJ-2A, 3A, 3B, 5, M38, M38A1

More Views

US Made Brake & Clutch Pedal Cross Shaft
Fits 48-71 CJ-2A, 3A, 3B, 5, M38, M38A1

USA Made Brake & Clutch Pedal Cross Shaft (1 required per vehicle)

Direct replacement for your worn out, egg shaped cross shaft. Tube that both the clutch and brake pedal arms attach to.

This cross shaft does not have the cotter pin at the bottom of the shaft by the key way. However, it can still be used on the early models as long as the clutch pedal is clamped onto the tube. Typically used with the 645086 style tube and bracket.

7-1/2" long

48-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
50-52 M38
52-66 M38A1

Item # Price

Availability: In stock

Add to Wishlist

Product Videos

Questions & Answers

Sort By: 


Questions: Is there a part number for one of these that fits a 1971 cj 5 with the 225 buick engine or is this the only one offered?
Question By: Josh Millspaugh on May 2 2018 3:57 AM
This is the only one offered.
Answer By: Willys Jeep Parts Tech on May 2 2018 6:12 AM
Questions: I have a 1971 CJ5 with a 225 V6 buick engine. My crossover tube does not have the tab welded on for the linkage to attach to. My system has a cable that runs from the clutch pedal to the throw out arm. Will this work for me?
Question By: Josh on Apr 24 2018 2:54 AM
I do believe they are a bit different for the V6 set up. But it possibly could be modified to work for your needs.
Answer By: Willys Jeep Parts Tech on Apr 24 2018 6:10 AM
I have been working on Jeeps for 48 years and the 70 & 71 CJs did use a cable that mounted to the clutch pedal arm on the outside of the frame and circled around to a bracket that mounted to the driver side of the transfer case and the internal cable continued forward to the clutch fork. the cross shaft DID NOT have the "stand" welded to the cross shaft since it was not needed and the shafts pivot housing which is riveted to the bottom of the frame had an extended tube toward the inside to fill the gap so the brake pedal would be properly located. This cable system never worked very well as the cable would distort and you would lose travel at the fork. Cut off the extended tube and use the A 497 shaft and go back to the pre '70s clutch linkage system would be my recommendation.
Answer By: Gary Holbrook on Jan 31 2019 2:15 AM
Questions: This shows 3 sets of holes for cotter pins is that true? The A495 shows only 2 sets. Is that true as you have said they are the same on the website. I need a # hole set for a GPW. Thanks
Question By: jay on Jun 4 2017 3:26 PM
There is only 2 holes for cotter pins on these.
Answer By: Willys Jeep Parts Tech on Jun 5 2017 5:45 AM
Questions: Will my existing woodruff key fit in this part, or do I need to buy a new one?
Question By: Nick on Feb 27 2017 1:53 AM
Yes, your existing should work.
Answer By: Willys Jeep Parts Tech on Feb 27 2017 5:48 AM
Questions: Is the only diff. between this and the A495 is this one is made in the USA ?
Question By: Floyd on Mar 29 2015 12:00 AM
Yes, that is correct.
Answer By: Willys Tech on Mar 30 2015 12:00 AM