Product Videos
Questions & Answers
Sort By:
Questions: do you have Item # D18BBSG in stock?
Question By: eddie on Jun 13 2020 7:38 PM
Yes, we sure do. Thanks
Answer By: Willys Jeep Parts Tech on Jun 15 2020 3:44 AM
Questions: Is this the right kit for a 62 FC 170?
Question By: Jim Rea on May 11 2020 5:30 AM
As long as your intermediate shaft measures at 1-1/4", it will be the correct kit. Thanks
Answer By: Willys Jeep Parts Tech on May 11 2020 4:05 AM
Questions: Hi,
I have just replaced all the gaskets and seals in the gear box and transfer case of my 3 speed CJ3b.
When i test drove it, both the front and rear transfer case prop shaft seals were leaking. THere seems to be no evidence of damaged seals or similar.
I was wondering if i over filled the transfer case. Does the fill hole also represent the full level?
Seems like the fill hole is above the output shaft level, which makes the seals work harder so to speak.
Any advice would be appreciated.
Thanks
Rob
Question By: Rob on Feb 19 2020 6:36 AM
If you didnt put some silicone on the front and rear output yokes splines then you tend to leak from there. I would apply a thin layer on the splines and also make sure you have your vent installed ontop of the case as well part number: A934
Answer By: Willys Jeep Parts Tech on Feb 19 2020 5:57 AM
Questions: Does this kit include the "Shim Pack" to set the output shaft Timken bearings end play?
Question By: Mike Mason on Nov 7 2019 5:07 PM
Youll want to add part number: A6753
Answer By: Willys Jeep Parts Tech on Nov 7 2019 9:26 AM
Questions: Our 62 Jeep Willys pickup gets vibration starting at 35 mp. there seems to be a little slack or play in the front and rear bearings of the transfer case. Would that cause the vibration?
Question By: Doug Isaacs on Aug 22 2017 3:42 PM
I would check your wheel bearings, steering, toe in/camber. Make sure they are all in spec. I would recommend part number: SJ-7100 steering stabilizer too.
Answer By: Willys Jeep Parts Tech on Aug 22 2017 8:46 AM
Questions: How do i know if my Dana Transfer is 1-1/8" or 1-1/4" Shaft ?.... My Jeep is an CJ3B 1955
Question By: Juan Pablo Ramos Ericastilla on Aug 25 2016 4:50 PM
In that year its 1-1/4" the way to confirm is just look on the backside of the case and measure the intermediate shaft in the middle that is held in place with the lock tab.
Answer By: Willys Jeep Parts Tech on Aug 25 2016 9:54 AM
Questions: Does this include output shaft pilot bushing?
Question By: Aaron Bohannan on Aug 24 2016 5:16 PM
A987 is the part number for that. It is separate.
Answer By: Willys Jeep Parts Tech on Aug 24 2016 10:37 AM
Questions: I have a '65 CJ-5 my transfer case make grinding sounds when i let off the gas and won't go into 4H and kicks it back down to 2H. Will the minor overhaul kit fix this problem or is it time to send it in for a full overhaul?
Question By: Devin on May 20 2014 12:00 AM
It should help for sure but it also sounds like you may have some bad gears.
Answer By: Willys Tech on May 21 2014 12:00 AM
Questions: Hello, is it possible to send in my transfer case for the overhaul process.
Question By: Anonymous on Feb 27 2014 12:00 AM
We sell complete rebuilds part number: 937477 and a few options will come up.
Answer By: Willys Tech on May 26 2016 10:59 AM
Questions: Is it common for the transfer case of a 1966 kaiser cj5 to have a minimal leak or should i be concerned and have it looked at. Thank you for your time. I love your Q&A options.
Question By: Anonymous on Nov 27 2013 12:00 AM
Yes they are leakers. We do sell a gasket set that will solve the problem.
Answer By: Willys Tech on Dec 2 2013 12:00 AM
Questions: I recently ordered this kit, anyway i can get some instructions, or a diagram of the transfer case, and parts.
Question By: Alan on Dec 27 2012 12:00 AM
We do have complete mechanics manuals. Our website will shortly have a full diagram section for the Dana 18. If you have any questions you can also call me toll free too.
Answer By: Willys Tech on Dec 27 2012 12:00 AM
Questions: Does this kit contain the felt seals for the output shaft behind the yokes and the paper gaskets for the rear cap?
Question By: Anonymous on Oct 11 2012 12:00 AM
Yes that is correct, it will have all the oil seals and felts seals too.
Answer By: Willys Tech on Oct 15 2012 12:00 AM
Questions: Does this kit include the clutch shaft bearing and if not, what is the part number for it (csn't find it in the catalog)?
Question By: Anonymous on Feb 18 2012 12:00 AM
Yes this kit will have all the bearings in the transfercase.
Answer By: Willys Tech on Feb 20 2012 12:00 AM
Questions: Your nomenclature states 55-66 for 1 1/4 intermediate shaft. Won't this also fit on a Dana/Spicer 18 t-case from a 1967 jeep with 1 1/4 inermediate shaft?
Question By: Kevin on Jun 27 2011 12:00 AM
Yes it should work just fine.
Answer By: Willys Tech on Jun 28 2011 12:00 AM
You Might Also Be Interested In
Weekly Willys highlights and discounts sent to your inbox
