Questions & Answers
Questions: Does this fuel pump come with the gasket?
Question By: Tyler on Apr 15 2022 6:32 AM
It sure does. Thanks
Answer By: Willys Jeep Parts Tech on Apr 15 2022 12:29 PM
Questions: fuel pump doesn`t fill up w/fuel but still runs. fuel barley over bottom port.
Question By: pete on Jan 29 2022 10:31 PM
Yes, that is normal and how designed.
Answer By: Willys Jeep Parts Tech on Jan 31 2022 5:36 AM
Questions: Hey Mike I bought a new single action fuel pump and it has a very fine crack in the glass bowl. I did not notice it a first until it got under pressure and began to leak. This is the divided two section bowl. Can I get a replacement? I didn’t see one online!Thanks, Dave
Question By: Dave Maynard on Dec 26 2021 1:34 PM
We can fix you up and get you a replacement. Please email email@example.com to help out.
Answer By: Willys Jeep Parts Tech on Dec 27 2021 5:43 AM
Questions: 48 CJ-2A, can I buy just the glass bowl gasket for my fuel pump? Thanks Mike
Question By: greg Cavanaugh on Nov 14 2021 6:22 PM
115656 is the part number
Answer By: Willys Jeep Parts Tech on Nov 15 2021 5:44 AM
Questions: Which of the threaded holes can I use for my heater core and what is the thread size and pitch of the hole I will be using?
Question By: Jason on Sep 14 2021 11:46 PM
This is a fuel pump, it wouldn't have anything to do with your heater. Thanks!
Answer By: Willys Jeep Parts Tech on Sep 15 2021 6:34 AM
Questions: i have 1948 jeep truck. i changed the dual action fuel pump to a single action. does it require a spacer or is it ok to go right on
Question By: rick bailey on Sep 5 2021 4:40 PM
Yes, people use single action pumps all the time.
Answer By: Willys Jeep Parts Tech on Sep 7 2021 5:39 AM
Questions: Do these fuel pumps run in a specific direction? The one on my cj5 looks like it's hooked up to flow away from the water pump side and then loops around the lower radiator hose and reconnects to the original steel fuel line.
Question By: Landon on Aug 10 2021 4:58 PM
Email firstname.lastname@example.org some pictures of your set up and we can help.
Answer By: Willys Jeep Parts Tech on Aug 10 2021 12:24 PM
Questions: Does your fuel pumps handle ethanol gasoline?
Question By: Tom on Jun 19 2021 4:59 PM
Yes, but I would available ethanol fuel if you can since it collects moisture.
Answer By: Willys Jeep Parts Tech on Jun 21 2021 6:06 AM
Questions: Does the fuel pump come with a new gasket?
Question By: Kurt on Apr 26 2021 10:24 PM
Yes, that is correct.
Answer By: Willys Jeep Parts Tech on Apr 27 2021 5:28 AM
Questions: I have a 1952 Willys Jeep Truck. I recently converted to 12 Volt. I was wondering about the fuel pump. The current one i have was vacuum to run the wipers. Do you have one that doesn't have the Vacuum? Please let me know.
Question By: Michael on Dec 23 2020 9:36 PM
Yes, this pump will work for just fuel on your 4-134 engine. You may just have to rotate the top a bit for clearance for your inlet fitting.
Answer By: WIllys Jeep Parts Tech on Dec 28 2020 6:10 AM
Questions: I purchased a glass topped fuel pump for my 51 M38 a couple months ago. I can’t seem to get it to work consistently, It will bubble and fill sometimes, other times it won’t fill at all? Then it will work perfectly for about a day and then out out nowhere just quit pumping altogether? The M38 floods all the time and is difficult to start. It has a brand new fuel tank, pick up, fuel lines and the Carter YS has been rebuilt, I believe the inconsistent running problem has to do with that fuel pump. The original was a two stage. I want to replace the glass top with the very best fuel pump for the M38. Which one would you recommend as the best and most dependable? Thanks! –Larry Johannes
Question By: Larry on Jun 21 2020 4:33 PM
If it sits up for a long time fuel tends to drain out of the carb. They never will fill up all the way. I would also take the diaphram off and check for any tears and debris that may have gotten into fuel pump from tank as well. Also make sure your fuel lines are away from a heat source.
Answer By: Willys Jeep Parts Tech on Jun 22 2020 5:54 AM
Questions: I have a 52 CJ3A with an 134L motor. I replaced the leaking fuel pump with a 119238 single action replacement. When we put it in my buddies thought it was wrong that the glass bowl was up instead of down. That, however is the only way it would go in. Since that time a few months ago the jeep has been starting very hard and running terrible uphill or with any load. A local mechanic said "I guarantee that it is upside down and that is the reason it is running badly". How should it be installed? Do I have the wrong fuel pump? Also, I did not use a spacer. Should I get one and add it? Thanks! Ray
Question By: Ray Beisel on Mar 25 2020 2:35 PM
It cannot be installed with glass down. The camshaft lobe pushes the arm up. Give me a call toll free. Happy to try to help you trouble shoot what all is going on with your Willys.
Answer By: Willys Jeep Parts Tech on Mar 25 2020 8:52 AM
Questions: I have a 48 CJ2A with the glass bowl fuel pump and discovered that it is leaking. It appears to be leaking from below the bowl where the top screws into the bottom. Is there a casket that goes between the two that could have fail and needs to be replaced. Also if there is a casket what is the part number. Thanks
Question By: Paul on Nov 19 2019 4:58 AM
115656 and A9293 will help you with this.
Answer By: Willys Jeep Parts Tech on Nov 19 2019 6:39 AM
Questions: I am restoring a 1948 CJ2A that has had the original fuel pump replaced with an electric pump. I need to replace and I am debated whether to go back to a mechanical pump or stick with the electric and if I switch back to the mechanical which model is best. Any advise would be appreciated. Thanks
Question By: Kelly McFarland on Jan 14 2019 7:59 PM
119238 is what we typically sell. But we also have a metal bowl design too and one that has a primer handle if you want to go that route as well.
Answer By: Willys Jeep Parts Tech on Jan 15 2019 6:09 AM
Questions: if i wanted to do away with the dual action fuel pump on my m38a1 will this fit the engine? i know i will have to reroute fuel lines. thanks
Question By: john on Nov 13 2018 8:56 PM
Give us a call toll free and we can go over the options. 888-648-4923. Thanks
Answer By: Willys Jeep Parts Tech on Nov 14 2018 6:51 AM
Questions: I have a L 134 engine on a Hobart welder it’s an industrial will this fuel pump work?
Question By: Dennis P on Nov 7 2018 7:50 PM
yes, this should work for you 4-134 L.
Answer By: Willys Jeep Parts Tech on Nov 8 2018 5:39 AM
Questions: I have a Omix-Ada 17709.01 Fuel Pump and afters removing the bowl several i find myself in need of a new bowl gasket have been searching for a while and have had no luck in finding one would you have any info?
Question By: Gary Estep on Sep 21 2018 4:24 PM
We do have it. The part number for the fuel pump bowl gasket is 115656. Thanks
Answer By: Willys Jeep Parts Tech on Sep 22 2018 6:36 AM
Questions: Will this fuel pump work on my 1954 m38A1?
Question By: Ryan on May 17 2018 12:24 PM
Yes, but youll have to re-run your lines and possibly rotate for front engine plate clearance.
Answer By: Willys Jeep Parts Tech on May 17 2018 5:58 AM
Questions: My Willy's 1947 CJ2A will turn over real well but it does not want to start up. I replaced the spark plugs this summer. The fuel pump looks to be leaking. Think the problem could be the fuel pump? Also, I have a primer handle on the dash board. Do I need to purchase the fuel pump with the primer handle or can I just make do with the fuel pump model without one? Thanks for your help.
Question By: Jim Rauschenbach on Mar 9 2018 1:53 AM
I would definitely start with replacing the fuel pump and if you have the type with the primer handle it may be good to stick with the same style. Give us a call toll free if you have any questions from here: 888-648-4923. Thanks
Answer By: Willys Jeep Parts Tech on Mar 9 2018 5:05 AM
Questions: DO HAVE THE GLASS BOWL FOR THIS FUEL PUMP MINE HAS A CRACK IN IT. IT IS FAIRLY NEW I DON'T TO REPLACE THE WHOLE PUMP.THANKS DONNIE
Question By: DONNIE on Mar 4 2018 12:59 AM
This does come with the glass bowl but you do have to buy the whole fuel pump to get the bowl. We do not sell just the glass bowl separately. Thanks
Answer By: Willys Jeep Parts Tech on Mar 5 2018 5:36 AM
Questions: I see you mention it is not normal to see fuel in the glass bulb in one of you responses. Mine is about half full of gas, does this indicate something is wrong? Currently trouble shooting lack of power, will be replacing the filter, curious if my pump is bad too. 1946 CJ2A
Question By: Ian Tibbs on Aug 27 2017 6:11 AM
No, there is nothing wrong with the glass bowl filling up or not. That is completely normal. Thanks
Answer By: Willys Jeep Parts Tech on Aug 28 2017 12:52 PM
Questions: Just order fuel pump for our 1964 CJ5 4-cyl. Did not realize replacement pump does not have vacuum connections. Need to return for correct replacement pump. What do you have available for use with two vacuum lines? Thks
Question By: john hornbostel on Aug 12 2017 12:53 PM
No problem on returns. Please give us a call toll free at 888.648.4923 and we can set up with an RMA number. Thanks
Answer By: Willys Jeep Parts Tech on Aug 14 2017 6:13 AM
Questions: I bought this fuel pump two years ago. Today when starting it for the first time in a few months the fuel pump began leaking around the bowl gasket. I took the bowl off and examined the gasket. No apparent decay. It was off tight from the box when purchased. Why is it leaking? Can the pressure build up between the pump and the carb?
Question By: bill on Jun 11 2017 3:10 AM
It could be a number of things really. Call us toll free and we can troubleshoot and replace if need be for you at no cost.
Answer By: Willys Jeep Parts Tech on Jun 12 2017 5:41 AM
Questions: I have a 1953 M38A1. Will the M38A1 start and run off a electric fuel pump only? A fellow collector told me that it will not start because it needs vacuum from the pump to start. I am an aircraft mechanic and have never heard of such a thing. I had a Dodge M37 that ran just great off a electric pump. Thanks
Question By: Larry Joy on May 27 2017 2:06 PM
An electric doesn't require vacuum. Just make sure you are not putting out more than 4.5 pounds.
Answer By: Willys Jeep Parts Tech on May 30 2017 5:25 AM
Questions: I have a 1965 cj5 Jeep 4cyl with the Hurricane original engine. About 20 years ago I replaced the fuel pump with an aftermarket unit that does not have the glass bowl, unfortunately I discarded the old pump (yes, that was dumb.) It's now time to replace the fuel pump again. The original fuel pump had vacuum wiper ports a glass bowl with a mesh filter built in (very easy to clean and diagnose fuel related problems.) So I'm looking to purchase a new fuel pump w/glass bowl which also has ports for the vacuum wipers. I don't see one on your site. Do you have one? If not, is there a way to add the vacuum wiper parts to the glass bowl style pump that does not have the vacuum wiper ports. I want the vehicle to be as close to original as possible.
Question By: Fred on Apr 18 2017 11:38 PM
735994 is the way to go. They don't make them with glass bowls. I would install an inline fuel filter too.
Answer By: Willys Jeep Parts Tech on Apr 19 2017 6:18 AM
Questions: What is the thread type and size of the inlet?
Question By: Kevin on Mar 25 2017 7:02 PM
It takes a 1/4" standard fuel line like original.
Answer By: Willys Jeep Parts Tech on Mar 27 2017 5:55 AM
Questions: I'm looking for a fuel pump for a F6-161 Cu. In. Hurricane engine. I can't seem to find one for the 161. Will this work?
Question By: Dennis on Oct 20 2016 2:58 PM
119482 is the part number you need for your 6-161 Willys engine
Answer By: Willys Jeep Parts Tech on Oct 20 2016 8:00 AM
Questions: I bought and installed Fuel Pump (single action) Item # 119238. I have it installed and ran fuel to it yesterday. The carb got fuel but the glass bowl did not show fuel. The gas was just barely visible coming into the unit. Does it need to be primed some how?
Question By: Mark Weller on Sep 30 2016 10:03 PM
It typically does not fill in the glass bowl. This is normal.
Answer By: Willys Jeep Parts Tech on Oct 3 2016 5:41 AM
Questions: Hello, I have one M38a1 with the original metal dual fuel pump.i want to go electric wipers and add a new fuel pump.I think that this pump will work.Just to ask,there is a thick spacer between pump and block in the military engines,do i need this or mount the pump to the block?i run on solex .
Question By: George Mirtsos on Jul 22 2016 6:50 PM
You can put the spacer back on there. You may have to rotate the diaphragm for clearance.
Answer By: Willys Jeep parts tech on Jul 25 2016 5:49 AM
Questions: I just received my new fuel pump. does it require gasket sealer?
Question By: Mark W Weller on Jul 15 2016 10:03 PM
Typically no, but it never hurts to use sealant.
Answer By: Willys Jeep Parts Tech on Jul 18 2016 5:42 AM
Questions: I could not start my GPW (later Willys L134 engine) so I installed the replacement fuel pump. Got it to run for a while (after priming the new Solex carb) off a small auxiliary fuel tank. However, when I connected the fuel line from the gas tank, would run for a few seconds from the priming, but then dies. I rodded out the fuel line (a while ago), fuel is fresh. What else needs to be done? I can't see any fuel in the glass bowl.
Question By: Harry Hoffman on Jun 11 2016 1:45 PM
When you are cold starting you need to pump the pedal just a bit when starting - not enough to flood - and choke it. It should give you the prime you need.
Answer By: Willys Jeep Parts Tech on Jun 13 2016 5:55 AM
Questions: Hi , i have a Willys year 1961 with following serial number 55468 10202 i need a new fuel pump to that motor are art no 119238 a good solution ?
Question By: Joachim Carlsund on Jun 5 2016 4:57 PM
Please call us toll free. We need more vehicle info and we can get you fixed up.
Answer By: Willys Tech on Jun 6 2016 5:54 AM
Questions: Is the fuel operated by a cam lobe or push rod?
Question By: Anonymous on Apr 29 2015 12:00 AM
The fuel pump arm rides on your lobe of your camshaft.
Answer By: Willys Tech on Apr 29 2015 12:00 AM
Questions: I have an M38 1950 Willys Army Jeep that probably needs a new fuel pump. Will this model work on my M38 jeep? Thanks, J.Johnson, Buda, Texas
Question By: jerrold johnson on Oct 7 2014 12:00 AM
It will work but on the M38 you may have to rotate the diaphram for any clearance issues.
Answer By: Willys Tech on Oct 8 2014 12:00 AM
Questions: What's the outlet pressure for this pump. i have a new solex carb that requires about 1.5 or so psi.
Question By: james nuttall on Oct 4 2014 12:00 AM
With the proper spacer they put out between 1.5 and 4 psi typically.
Answer By: Willys Tech on Oct 6 2014 12:00 AM
I put an adjustable fuel pressure regulator on mine. They aren't expensive.
Answer By: Joel Merrill on Apr 23 2021 4:59 PM
Questions: Need replacement coil for 51 willys m38 converted to 12 volt what do you recommend. Thanks bob
Question By: Bob on Jun 9 2014 12:00 AM
933160 & MSD8213 are the two part numbers you will need.
Answer By: Willys Tech on Jun 10 2014 12:00 AM
Questions: I replaced my old dual action fuel pump with the glass bowl single action. I have fuel from the tank, through the filter and up to the pump. The pump arm is on top of the cam and I used a spacer. Fuel from the tank is attached on the left with the arrow pointing toward the pump. Line to carb is attached to the right side of the pump with the arrow pointing away. I have pumped the pedal to try and prime and yet I get no fuel through the pump. No gas in the bowl. Nothing! Do you have any thoughts?
Question By: kevin gray on May 17 2014 12:00 AM
I would check the pump for suck/blow on the inlet and outlets by hand in a vice. I would also check to make sure there are no blockages in the tank and plenty of fuel.
Answer By: Willys Tech on May 19 2014 12:00 AM
Questions: I have a 63 willys here in my shop and was wondering if there is a replacement screen for the bowl style fuel pump
Question By: brandon on Apr 18 2014 12:00 AM
That would only be available used. Or this fuel pump above will have a new one in it.
Answer By: Willys Tech on Apr 18 2014 12:00 AM
Questions: I just bought the pump from you for my 60 CJ-5 and I wanted to know if I need the spacer between the pump and the block. I bought it just in case I did and I wanted to get your opinion before install it.
Question By: Rick Harding on Feb 12 2014 12:00 AM
They are there originally and I recommend them. They are part number: 866236
Answer By: Willys Tech on Feb 17 2014 12:00 AM
Questions: I rebuilt my carb in 56 willys and now cannot get fuel to carb. Did I do something wrong in rebuild? Or does fuel pump need to be primed somehow?
Question By: Anonymous on Nov 2 2013 12:00 AM
You should be able to bench test it for suck and blow. You may want to check your tank for any blockages as well.
Answer By: Willys Tech on Nov 4 2013 12:00 AM
Questions: my original pump is dual action. I do not have wipers. I bought this single action to replace it. what do I do with the inlet and out let vacuum lines?
Question By: jordan on Oct 13 2013 12:00 AM
This is a single action pump, there is no vacuum hook up on it. Only inlet/outlet for fuel.
Answer By: Willys Tech on Oct 14 2013 12:00 AM
Questions: Does this come with mounting instructions? I have a 47 CJ2A, and when i got it it had a electronic fuel pump on it, and I wish to replace it with an original style one. Also is this pump ready/good to go for modern fuel?
Question By: SteveBerry on Oct 8 2013 12:00 AM
It is all ready for modern fuel. If you have any questions on install you can call us toll free. It basically just bolts up.
Answer By: Willys Tech on Oct 9 2013 12:00 AM
Questions: 17701.02 carb calls for 2 psi or less my 62 cj5 dual pump puts out a steady 4.5 psi at idle do i put in an inline regulator ? or do get this spacer that you refer to and if so where do i get one? thanks.
Question By: jim on Jul 20 2013 12:00 AM
You should put out no more than 2.5 pressure. Yes I would get an inline regulator or you can get a good used spacer to cut the pressure down.
Answer By: Willys Tech on Jul 22 2013 12:00 AM
Questions: 1) What is the pressure delivered by this pump? 2) I have a Solex on a 3A. It seems to run well without a pressure regulator. What would be the symptoms of the pressure being too high? 3) I have a lean main jet in my Solex (112), because I live at 6,000ft. If I find that the pump delivers too high of a pressure, is a leaner jet going to have the same effect essentially as a pressure regulator? I find that these inexpensive dial style pressure regulators do not work well consistently."
Question By: Tom on Jun 6 2013 12:00 AM
These pumps will put out appox 2 pounds of pressure. It is recommended that you use the original spacer place between the pump and the block as well. They function just like original. If you are stalling out or leaking or even fouling out plugs you are running with too much pressure or are too rich in the carb.
Answer By: Willys Tech on Jun 7 2013 12:00 AM
Questions: Just purchased the #119238 fuel pump. My 1951 Cj3a has a pump on with a spacer between the block and pump. Old pump is not duel action and does not have a glass bowl. Do I need this spacer with this new pump? Reviewed an article stating the 3a original pump needed the spacer. If changed to a single action do not need spacer. Is this the original type for a 1951 3a? Thanks
Question By: kris kinsey on Mar 1 2013 12:00 AM
Yes I would put the spacer back on there. They are good to cut down on fuel pressure.
Answer By: Willys Tech on Mar 4 2013 12:00 AM
Questions: I just bought the new single action to replace the dual action on my 55 cj. I cant install the new pump because the front engine mount blocks the fuel line. I thought i would go with electric wipers and didnt need the dual.is the dual the only choice? Thanks.
Question By: chuck on Oct 19 2012 12:00 AM
You can rotate the diaphram on it and just use a 90 degree fitting on it. It should work fine for you.
Answer By: Willys Tech on Oct 22 2012 12:00 AM
Questions: Have 1948 cj2a, L134 engine, have mechanical fuel pump on with the metal bowl down, it should be up? I have in install incorrectly? Went to town and it died, would only start with choke all the way out. Has been running fine up till today for about a year. Was recommened that i put new fuel pump and a electric one as well. What is your recommendation? Thank you in advance.
Question By: Tom on Aug 25 2012 12:00 AM
Your pump you have on there now is unoriginal. The way the bowl is oriented depends on the way the arm is make on the pump where it hits the camshaft. The bowl on this pump goes up like original.
Answer By: Willys Tech on Aug 27 2012 12:00 AM
Questions: hi - bought a fuel pump from here about a year ago and it has the bowl on the top - do you have one that has the bowl on the bottom - that is what my 1953 cj3 originally had. Thanks, Kerry Wenzl.
Question By: Kerry on Aug 18 2012 12:00 AM
They were originally bowl on top. This is proper for your vehicle.
Answer By: Willys Tech on Aug 20 2012 12:00 AM
Questions: I have a 1961 willys cj3b. The fuel pump works but it is leaking fuel from a small hole in the center of the pump. it is a dual action pump. Is it something I can repair or does it need replacing. If needs replacing will the single action work? I have electric wiper motors now and don't need the vacuum
Question By: dan on Aug 10 2012 12:00 AM
Sounds like it could be a bad diaphram in your old pump. If you are running electric wipers then this one should work just fine.
Answer By: Willys Tech on Aug 10 2012 12:00 AM
Questions: 1950 Willys Jeepster 4-134 F Head, thought we just ran out of gas filled her up would not start, primed carb runs until prime is out. blew out all the fuel lines and cleaned the fuel pump screen. fuel pump is a single action with glass bowl seems to work because it fills up with gas but does bubble. cannot get fuel to carb. do I need a new fuel pump the one I have was new in 2009?
Question By: Jerry on Jun 30 2012 12:00 AM
Sounds like a stuck valve or bad diaphram but its hard to say. This fuel pump will solve your problem.
Answer By: Willys Tech on Jul 2 2012 12:00 AM
Questions: My 52 cj-3a has this fuel pump #119238. It takes a long time to get it started. Will it help to put a 6 volt pump on. To pump the fuel to the carb, befor trying to start.
Question By: Anonymous on Apr 20 2012 12:00 AM
When you start make sure to pump the pedal a few times to get the fuel going. If you let the vehicle sit up it can be alittle hard to start.
Answer By: Willys Tech on Apr 23 2012 12:00 AM
Questions: Do you make an electric fuel pump for a 1946 CJ2A? If so what part number? Thanks, Harry
Question By: Harry on Apr 18 2012 12:00 AM
I dont recommend them. They put out too much fuel. I would stick with this one.
Answer By: Willys Tech on Apr 19 2012 12:00 AM
Questions: I am restoring a 54 cj3b totally stock. Is this the right one?
Question By: tink on Sep 10 2011 12:00 AM
It should help. When you start your vehicle pump the pedal a few times prior to get the fuel going and prime it.
Answer By: Willys Tech on Oct 3 2011 12:00 AM
Questions: Do you carry the double action pump with the glass bowl?
Question By: JD on Jul 19 2011 12:00 AM
Double actions only come in metal bowl.
Answer By: Willys Tech on Jul 19 2011 12:00 AM
Questions: The fuel pump currently installed does not have the glass bowl at the bottom. Which is more like the original on the '46 CJ2?
Question By: Peer Plaut on Mar 28 2011 12:00 AM
The glass shown here is like original.
Answer By: Willys Tech on Mar 28 2011 12:00 AM
Questions: is the glass bowl on the bottom?
Question By: Jim on Feb 2 2011 12:00 AM
The glass bowl goes up.
Answer By: Willys Tech on Feb 2 2011 12:00 AM
Questions: Does the fuel pump 119238 have a split bowl, which is different from original ?
Question By: Anonymous on Jan 8 2011 12:00 AM
They are just like the originals.
Answer By: Willys Tech on Jan 10 2011 12:00 AM
Questions: I bought the fuel pump #119238 for my 1945 gpw. I installed it and the jeep started right up with a little primimg to the carb. The question I have is as the vehicle runs the gas in the bowl doesn't get much more then just off the bottom of the bowl and over the screen. How high is the gas suppose to get in this bowl? It seems to be running right at a stand still in the garage but before I take it out I just wanted to be sure it's correct and I won't break down.
Question By: Phil Galvano on Nov 4 2010 12:00 AM
It doesnt fill up all the way typically. The bowl will fill up alittle more or less depending on speed/pressure. Sounds like your good to go.
Answer By: Willys Tech on Nov 8 2010 12:00 AM
Questions: Will this pump work for a CJ-3B? The origianal had a dual action pump on it.
Question By: Ben on Oct 19 2010 12:00 AM
The glass bowl goes up and you just have to use a 90 degree fitting on this. They work great for your vehicle
Answer By: Willys Tech on Oct 20 2010 12:00 AM