Pinion Shaft Yoke
Fits 41-71 Jeep & Willys w/ Dana 25 Front & 27/41/44 Rear

More Views

Pinion Shaft Yoke
Fits 41-71 Jeep & Willys w/ Dana 25 Front & 27/41/44 Rear

New Pinion Shaft Yoke

With 10 spline.

Dana 25 Front
Dana 27/41/44 Rear

41-45 MB
45-45 GPW
45-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
50-52 M38
52-66 M38A1
46-64 Truck
46-64 Station Wagon

Item # Price

Availability: In stock

Add to Wishlist

Product Videos

Questions & Answers

Sort By: 


Questions: does this yoke fit 1310 u joints, or the smaller 1210?
Question By: RON ROBERTS on Nov 24 2022 7:18 PM
See part number: 8126614S
Answer By: Willys Jeep Parts Tech on Nov 28 2022 5:36 AM
Questions: Is the dust shield on this much smaller than the original? Also does it come snug. My dust shield became lose and rattled excessively. It also seems much larger than this one.
Question By: John on Jun 2 2020 10:54 AM
There are different versions used thru the years and sizes of shields.
Answer By: Willys Jeep Parts Tech on Jun 2 2020 5:53 AM
Questions: I have a 55 Truck with a 226. Both drive shaft have Cleveland style U joints. If I go to this yoke, is it still compatible with the Cleveland style ends on the drive shaft, or will I have to rework the drive shafts too?
Question By: Jim Willingham on Apr 28 2020 1:51 PM
Sorry, it is for U-bolt style only. We can help you on used. Please email
Answer By: Willys Jeep Parts Tech on Apr 28 2020 7:18 AM
Questions: I have a 1950 Willy station wagon I put a 305 sbc with 3 speed 350 Transmission. I need to get a drive shaft that fit Th 350 transmission and work with the rear end in the willy wagon. Will the Pinion Shaft Yoke A1445 work with a GM drive shaft that has U-joints?
Question By: Gene on Apr 16 2020 12:06 AM
Your best bet is to have a driveshaft place fabricate one for you given all your changes.
Answer By: Willys Jeep Parts Tech on Apr 16 2020 5:56 AM
Questions: Once the crown nut is tightened, should it be backed off to allow the cotter pin to be installed (in the video, the crown nut seems to spin loosely), or should it be as tight as possible? Also, after I installed the oil seal, I tapped in the yoke as far as it would go, and then installed the washer, crown nut, and cotter pin. Once that was done, however, the drive shaft felt as if it was binding against the oil seal, and it was difficult to turn by hand (in the video, the yoke seemed to turn freely by hand). Did I over-tighten the nut or tap the yoke in too far?
Question By: Craig on Jan 25 2017 10:17 PM
We usually use a nylon lock nut and torque to 65-75 lbs. If using a castle nut I would still try to maintain this spec if possible after installing cotter pin. Your mechanic manual will detail as well.
Answer By: WIllys Jeep Parts Tech on Jan 26 2017 8:51 AM
Questions: Will this Yoke fit on a 1969 CJ5 with a DANA 27 Front Axle
Question By: Roland Mayer on Dec 29 2016 2:24 PM
Yes, as long as you are 10 spline. Typically though you see 19 spline on that year Dana 27.
Answer By: Willys Jeep Parts Tech on Dec 29 2016 7:24 AM
Questions: Your picture shows a 10 spline yoke. I need a 26 spline yoke. Do you have such an item in stock?
Question By: Jim on Aug 20 2016 5:18 PM
I need more vehicle in formation. Please call us toll free and we can help.
Answer By: Willys Jeep Parts Tech on Aug 22 2016 6:05 AM
Questions: Is there a dust shield that would cover the oil seal on the front Dana 25? I didn't pull one off but it looks as though there should be something there like on the rear yoke going into the Dana 44.
Question By: Alex Darling on Nov 14 2011 12:00 AM
We can probably get you good used. Please call us toll free.
Answer By: Willys Tech on Nov 15 2011 12:00 AM
Questions: Is there some type of seal that goes into the dust shield? The yoke is like the one pictured, but there istype of seal in it and I can't find it listed.
Question By: Anonymous on Sep 6 2011 12:00 AM
There is the pinion seal and pinion seal gasket. They are part numbers: 639265 & 636565
Answer By: Willys Tech on Sep 7 2011 12:00 AM
Questions: The pinion shaft yoke, does this keep gear oil from leaking or is there another seal behind the emergency brake assembelly
Question By: donnie on Mar 5 2011 12:00 AM
There is a pinion shaft oil seal: 639265 and the output seals: 923896 & 932295
Answer By: Willys Tech on Mar 7 2011 12:00 AM