Spicer Style Driveshaft Universal Joint
Fits 41-66 MB, GPW, CJ-2A, 3A, 3B, 5, M38, M38A1

More Views

Spicer Style Driveshaft Universal Joint
Fits 41-66 MB, GPW, CJ-2A, 3A, 3B, 5, M38, M38A1
New Spicer Style Universal Joint (4 required per vehicle)

Includes complete universal joint with bearing caps and retainer clips. Attaches yoke and propeller shaft ends together on 4wd vehicles.

41-45 MB
41-45 GPW
46-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-66 CJ-5
50-52 M38
52-66 M38A1
Item # Price

Availability: In stock

Add to Wishlist

Product Videos

Questions & Answers

Sort By: 


Questions: Do you sell just the bearing caps & Pins? Thanks. 1964 CJ5 Willys F134.
Question By: Kyle Forbes on Nov 7 2020 1:37 AM
Give me a call toll free so we can see if we can get that set up for you. Thanks
Answer By: Willys Jeep Parts Tech on Nov 9 2020 3:51 AM
Questions: - I have a Cj3a and need to replace the passenger front knuckle U joint. Is this the correct replacement part? - Also is this the same U joint used on my F&R drive shafts? - My inner axle tubes have FLAT brass washers pressed into them what is required when using the splicer joint ? Thank you for time.
Question By: CJ on Apr 22 2019 5:04 PM
Can you email an image of what you have in your vehicle currently so we can confirm.
Answer By: Willys Jeep Parts Tech on Apr 22 2019 10:49 AM
Questions: What size ujoints are these? 1310? What is the diameter of the cap and the length of the ujoint? Thanks,
Question By: Hank on Jul 11 2018 9:49 AM
Diameter 1.650 at end caps. Overall length 3.25 end cap to end cap across.
Answer By: Willys Jeep Parts Tech on Jul 11 2018 6:41 AM
I checked those dimensions and they are for 1310, 297X and 760X. All the same dimensions.
Answer By: Hank on Jul 11 2018 11:15 PM
Questions: I have a Jeep I built when I was in California to go on the trails. It has a lot of miscellaneous parts on it. The rear driveshaft has spicer u-joints that have a number on the cap (P051), the front ones have a different one (P541) and are smaller. Which ones do I need? The front from end to end is 2.44 and the cap is 1.065. The rear are 3.22 end and 1.076 cap.
Question By: Kenny Wright on Jul 28 2016 5:35 PM
Sounds like you have a later CJ-5 1966+ Please call us toll free and we can ID what you have there.
Answer By: Willys Jeep Parts Tech on Jul 28 2016 11:26 AM
Questions: I have a 66 CJ5 with the Dana 27 ront, Dana 44 rear, and Dana 18 transfer case. Dauntless V6. Will these u-joints fit the front and rear driveshafts?
Question By: Anonymous on Jun 25 2014 12:00 AM
In that year you could have these or part number: 937340
Answer By: Willys Tech on Jun 26 2014 12:00 AM
Questions: I have a universal joint with no snap rings. Instead there is a milled portion of all four ends to accept retaining clips that are bolted to the yoke. The universal joint has to be installed between all four yokes then the end caps with needle bearings have to be pushed onto the ends of the universal joints. Then the retaining clips are bolted onto the yokes to hold the assembly together. I cant find anything like it in any of your catalogs.I need to replace many of these as they are shot.
Question By: kevin on Jun 27 2012 12:00 AM
Sounds like you have the cleveland style joint. Part number: 924189 will replace it. They typically used that style on Willys Truck and Station Wagons.
Answer By: Willys Tech on Jun 29 2012 12:00 AM