Questions & Answers
Questions: If I tighten the 3 bolts on the bearing retainer my transmission gets tight and I cannot turn the yoke. Is there a shim that needs to be added ?
Question By: Jim Ibberson on Oct 13 2019 6:15 PM
No shim at the front bearing cap. Your new grease seal is most likely just tight in the front. They are hard to turn by hand when new.
Answer By: Willys Jeep Parts Tech on Oct 14 2019 6:26 AM
Questions: How come you don’t have clutch releases pin on the other side for left hand clutch and if you do is it a different part number
Question By: Gary on Oct 16 2018 3:34 PM
You can use this as a LH drive too. You just need to move the fulcrum.
Answer By: Willys Jeep Parts Tech on Oct 17 2018 5:42 AM
Questions: I have a 59 Willys with a T90 transmission the number stamped in my retainer is 3741458. Is this the same retainer?
Question By: tom on Feb 11 2018 7:43 PM
Yes, as long as you have a 4 cylinder engine. If you have the 6 cylinder - 906201 - this is correct number. Thanks
Answer By: Willys Jeep Parts Tech on Feb 11 2018 12:31 PM
Questions: Is the upgraded new neoprene seal it comes with the same as the one sku# 645985
Question By: Jax on Sep 9 2017 6:36 PM
Yes, this will have the neoprene seal in it.
Answer By: Willys Jeep Parts Tech on Sep 11 2017 10:52 AM
Questions: Says it comes with new neoprene seal. Does this stop the oil from traveling into the bell housing, because the felt seal don't stop it and now my clutch is oil soaked and slipping. I've heard I can get a sealed bearing and replace the front bearing with it, but if this new cap and seal stops the problem, I wouldn't need to pull the shaft and bearing.
Question By: Richard Chapman on Aug 28 2017 6:03 PM
this prevents any transmission fluid from leaking into your bell housing that is correct.
Answer By: Willys Jeep Parts Tech on Aug 29 2017 5:42 AM
Questions: does this cap fit over bearing. outside bearing is 3 1/8. and is the inside diamiater of shaft 1 1/8 ? thank you
Question By: rodney on Aug 15 2017 9:47 PM
This bolts to the outside of the transmission case. It slides over the input shaft.
Answer By: Willys Jeep Parts Tech on Aug 16 2017 5:52 AM
Questions: Does the neoprene seal replace the felt seal? Or do I still use the felt seal?
Question By: Karl on Jul 22 2017 2:17 PM
Yes, that is correct. It replaces it
Answer By: Willys Jeep Parts Tech on Jul 24 2017 5:57 AM
Questions: will this fit T 96 -1B overdrive W.G.D.W ?
Question By: Albert on Jun 29 2017 7:53 PM
Sorry, this is for the T-90 transmission only.
Answer By: Willys Jeep Parts Tech on Jun 30 2017 5:57 AM
Questions: Two questions: 1. How much play should the main drive gear shaft have in this bearing retainer cap? Mine is not snug. 2. Is there a way to remove and replace the front bearing (mine has a little play in it) without removing the entire main drive gear shaft from the tranny?
Question By: Jeremiah F Cornell on Feb 9 2017 7:13 PM
You should snug. There should be approx. .003" on end play. Sorry, you will have to dissemble the transmission to replace the front bearing.
Answer By: Willys Jeep Parts Tech on Feb 9 2017 11:56 AM
Questions: I have the T90 paired with a dauntless v6 225. I need the correct front bearing retainer. Can you help. I have one but it is broken. Thanks!
Question By: Anonymous on Oct 8 2014 12:00 AM
906201 is probabaly the one you need if you have the V6-225 up there.
Answer By: Willys Tech on Oct 8 2014 12:00 AM
Questions: ok I got part number 640422 and the pin for the clutch release is on the wrong side how do I remove it or do you have one with it on the opposite sidemine needs to pin on drivers side
Question By: damian on Jun 29 2014 12:00 AM
It will just press off and press into either side.
Answer By: Willys Tech on Jun 30 2014 12:00 AM
Questions: does this retainer come w/ the neoprene oil seal,or does it use the felt seal.
Question By: Anonymous on Jan 1 2013 12:00 AM
This is just the steel cap itself. It can take either Im sure.
Answer By: Willys Tech on Jan 2 2013 12:00 AM
Questions: does the throw out bearing spring hook to this retainer in the hole opposite the fork ball stud
Question By: Anonymous on May 21 2012 12:00 AM
Yes that is correct.
Answer By: Willys Tech on May 21 2012 12:00 AM
Questions: Does this cover come with the fork pivot ball included?
Question By: bob on Jan 4 2012 12:00 AM
Yes, that is correct.
Answer By: Willys Tech on Jan 4 2012 12:00 AM
Questions: I have a 1956 jeep willys wagon with a 283 chevy small block. will this retainer fit the transmission along with the adptors currently on it? the housing for the adaptor has 4 bolt holes.
Question By: charles 45 on Oct 26 2011 12:00 AM
Yes as long as you have the original T90 transmission that still uses the same retainer cap as the 4-134 engine.
Answer By: Willys Tech on Oct 26 2011 12:00 AM