Save 10% Off All Brake Parts Enter STOP10 at checkout.

FREE SHIPPING on all orders $98+ See Details

Select Your Currency
Close
  • Africa
  • Americas
  • Asia
  • Europe
  • Oceania
Shop Kaiser Willys

Speedometer Drive Gear
Fits 41-71 Jeep & Willys with Dana 18 transfer case

Part # A1511

New Speedometer Drive Gear (1 required per vehicle)

Proper gear to drive your speedometer cable to give proper MPH reading.

Application:
Dana 18 Transfercase

Fits:
41-45 MB
41-45 GPW
46-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-71 CJ-5
50-52 M38
52-66 M38A1
46-64 Truck
46-64 Station Wagon

Part # Price
A1511

$17.99

MSRP:

$17.99

MSRP:

1 Item has been added to your cart!
Close

Product Videos

Questions & Answers

Please Wait...

Ask Question Add Answer

All questions will be displayed after moderation. All answers will be displayed after moderation.

1962 cj6 w/ dana 44 rear and dana 25 front differential. My drive gear for the speedometer spins on the shaft and the speedometer cable gear does not match the tooth pattern. I was told that the gear ratio makes a difference on which speedo gears you need, i have 14 teeth on the speedo cable gear and the drive gear has 9 i think, could be 8. Any suggestions?

Willys Jeep Parts Tech:
Any more there really is only the one gear available and they read pretty accurate overall.

On a CJ 3b the speedo cable turns the opposite direction to what it is supposed to, that is the speedo works fine if the car is in reverse, but not forward! The drive gears appear to be correct, and the speedo is a new replacement. any clues? Note the turn direction on the old speedo and the new are the same.

Willys Jeep Parts Tech:
I think maybe the A1511 is installed backwards but Im just guessing what someone has done to make it do this. It is a gear on gear connection so, that is very unusual.

My speedometer gear turns free on the shaft. When you say it presses onto the shaft, is it tight or snug? Mine pins easily, Do I need to replace it?

Willys Jeep Parts Tech:
Please email mike@kaiserwillys.com I can help out and see what all is going on with your gear.

Am replacing the rear seal on Transfer case and rebuilding hand-brake assembly on my '61 CJ-3B. Speedo drive gear spins freely on the output shaft. Is that right? What makes it turn with the shaft? The speedometer seemed to be working fine before disassembly.

Willys Jeep Parts Tech:
The drive gear A1511 is pinched by the rear output yoke. Make sure that is in place properly.

Is the gear suppose to turn freely on the output shaft or should it press on the shaft?

Willys Tech:
It presses onto the shaft.

this gear go's allthe way to the seal or it stops in the middle of the shaft , i think mine is reamed out .the part that this turns dosen't touch it.

Willys Tech:
They are positioned approx 2/3rd the way up the shaft.

Can this be installed without removing the transfer case?

Willys Tech:
Yes. Just unbolt the rear bearing cap where your driveshaft hooks up.

when i disconnect/connect speedometer cable, speedometer gauge works for a few seconds. Is it the cable or something else. thank you

Willys Tech:
Sounds like it could be the cable or drive gear.

Do you have the driven speedometer gear, the one that mates to the above gear, that actually turns the speedometer cable?

Willys Tech:
We have a few options. Please call us toll free.
Request Catalog
X
THANK YOU! Your catalog request has been submitted successfully. Please note:

If your catalog does not arrive within 7-10 business days, call us Toll-Free at (888) 648-4923.

Email Subscription
X
THANK YOU! You have successfully subscribed to our newsletter.
Contact Form
X
THANK YOU! Your contact form request has been submitted successfully.
Photo Contest
X
SUCCESS! Your photo contest entry has been submitted!
Browser warning
The browser you are using to visit our website is no longer supported. For the best browsing experience, please visit us using a different browser.
I understand, close this message