Questions & Answers
Questions: Another asks if the throttle/choke cables are the same. My choke cable seems long/smashed against the firewall and unable to move with the choke now on the side and not the rear. How is the choke cable run? Does it need to be shortened?
Question By: Nick Shaw on Sep 6 2020 1:42 PM
They are the same other than the engraved knob. They are cut to length.
Answer By: Willys Jeep Parts Tech on Sep 8 2020 5:46 AM
Questions: I have a 1950 truck with an F head engine. Mine needs to hook to vacuum line does this have the fitting, and should it work ok for my application thank you
Question By: Jim on May 26 2020 10:43 PM
I do believe this has a vacuum port. Usually though this is off the fuel pump.
Answer By: Willys Jeep Parts Tech on May 27 2020 12:55 PM
Questions: Do you sell the recommended "in-line fuel pressure regulator, between the fuel pump and the carburetor to a low setting of 1.75 to 2 pounds? If yes, what's the part number?
Question By: Micheal Godlove on May 26 2020 7:52 PM
12804 is what i recommend for it.
Answer By: Willys Jeep Parts Tech on May 26 2020 1:01 PM
Questions: 52-66 M38A1 (with modification) whats the modification needed?
Question By: charles on Apr 19 2020 5:27 AM
The original carburetor was a side draft. This one is a down draft. The modification would be to make sure you have an air horn to give it the proper bend. That number is 809785. Thanks
Answer By: Willys Jeep Parts Tech on Apr 19 2020 2:25 PM
Questions: I installed this carburetor and it was working great. I spent a day getting my new gas pedal linkage prefect, the throttle was open and closed probably 50 times. Now it is sticky. It doesn't auto return to closed. No linkage is connected. It's the shaft in the carb sticking.
Question By: Carmen Piunno on Apr 11 2020 7:31 PM
Make sure you are not running any bad gas. Non ethanol. Please email email@example.com and we can help out.
Answer By: Willys Jeep Parts Tech on Apr 13 2020 6:46 AM
Questions: I have a 47 2A with a F4-134 motor in it, will this carb allow me to go back to an original low profile hood without a cut out in it? Also, what air cleaner will I need to run with it?
Question By: James Johnston on Apr 1 2020 1:24 AM
Sorry, it will not.
Answer By: Willys Jeep Parts Tech on Apr 1 2020 5:49 AM
Questions: Do you sell a dry air filter that fits this carburetor?
Question By: Stephen Barnett on Jan 6 2020 6:59 PM
Sorry, you have to use your original oil bath.
Answer By: Willys Jeep Parts Tech on Jan 6 2020 11:15 AM
Questions: Bought a new Solex carburetor from you all for my 1956 CJ5 F head engine. Engine also has a new fule pump just like the old with the vacume. Teh carb seems to be overloading with fuel. Any help would be appricated.
Question By: Jerry on Aug 20 2019 8:25 PM
Make sure your fuel pressure is below 3-3/4 pounds. Email firstname.lastname@example.org and we can help you out too. Thanks!
Answer By: Willys Jeep Parts Tech on Aug 20 2019 1:39 PM
Questions: New Replacement Solex Carburetor Fits 53-71 CJ-3B, 5, M38A1 with 4-134 F engine I have a '48 CJ2 with the F134, Carter carb, Hood is cutout to allow for carb Will this Solex allow use of the original flat hood"
Question By: Glover on Jul 4 2019 9:03 PM
Yes, if you have the 4-134 F motor then this would be the one for you.
Answer By: Willys Jeep Parts Tech on Jul 8 2019 5:41 AM
Questions: I have a 1954 m38A1. My carb has AISAN YF stamped on it. Will this 923808 work for a replacement?
Question By: Duane on Feb 23 2019 8:49 PM
The YF you have on there is unoriginal. But the 923808 does fit for the M38A1.
Answer By: Willys Jeep Parts Tech on Feb 25 2019 5:39 AM
Questions: I bought a new carburetor from you 02/17/2017, order number 340318A. I only got things running here in the last two weeks. I have fuel delivered by an electric fuel pump and get fuel to the carburetor. The carburetor will not take fuel. If I prime the carb, it will start and run. If I leave it over night, I will have to prime it again. What am I missing? Tim.
Question By: Tim Boychuk on Feb 21 2019 11:50 PM
Make sure your not putting out too much fuel pressure. Electrical ones tend to put out way too much over 4.5 pounds. Email email@example.com and we can help out on the hard starting.
Answer By: Willys Jeep Parts Tech on Feb 22 2019 5:52 AM
Questions: I have a 1963 CJ5, and I'm going to install a turbocharger to it, this carburetor can be installed to work like a blown carburetor? if not, which carburetor might I use?
Question By: Erick Vizcaíno on Oct 3 2018 10:51 PM
I dont think a turbo charger is going to work for this application.
Answer By: Willys Jeep Parts Tech on Oct 4 2018 5:37 AM
Questions: Will this fit a super hurricane 6 cylinder l engine
Question By: Butch on Sep 11 2018 10:28 PM
644436 is the carburetor for the 6-226 engine.
Answer By: Willys Jeep Parts Tech on Sep 12 2018 5:59 AM
Questions: can I hook up my manual throttle to this...how?
Question By: John Lernartz on Aug 17 2018 12:19 AM
Yes, there is a bracket on the side to allow for the manual hook up.
Answer By: Willys Jeep Parts Tech on Aug 21 2018 5:51 AM
Questions: Do you know if there is an in tank electric fuel pump/sending unit and a throttle body for a 1956 134-f engine available anywhere?
Question By: Hollis on Jun 19 2018 12:53 AM
Sorry, no. Only mechanical.
Answer By: Willys Jeep Parts Tech on Jun 19 2018 5:51 AM
Questions: my first solex carb for my 1955 cj5 was stamped solex on the top plate and on the accelerator pump plate this was back in 1998 still ave this carb it's fine//just got a new one for a 1958 cj5 it has no name on it //is this a real solex carb?/number on it is P-3LE///12-20_17///help thanks //Art
Question By: arthur skidmore v on May 29 2018 9:01 PM
If you got it from KWAS then its a Solex. If you got it somewhere else, send me a photo to firstname.lastname@example.org and I'm happy to take a look for you. Thanks!
Answer By: Willys Jeep Parts Tech on May 30 2018 6:18 AM
Questions: Hello, I have a Carter YF 938S on my engine and I was wondering if this should work?
Question By: Nick on Mar 12 2018 5:07 PM
Yes, this would be a replacement for that.
Answer By: Willys Jeep Parts Tech on Mar 12 2018 10:37 AM
Questions: I need a carburetor that has a shorter profile. I have put a F134 engine in an MB body. can this work as a lower profile so the hood will close?
Question By: Terry Martin on Jan 17 2018 12:03 AM
You will probably have a clearance issue given the 4-134F motor. Call me toll free. I can try to help you out. Ask for Mike M.
Answer By: Willys Jeep Parts Tech on Jan 17 2018 5:46 AM
Questions: this carburetor looks a little different then the one I have. I have a 1955 cj5 and the carburetor is a carter yf
Question By: jim on Dec 10 2017 11:12 PM
It is not the original carburetor for the CJ-5. It is an aftermarket replacement carburetor that will replace the original YF carburetor. It will fit on top of the manifold and use the original linkage, no problem. It will work just fine.
Answer By: Willys Jeep Parts Tech on Dec 11 2017 5:38 AM
Questions: I have a 53 m38 a1. The carb looks taller and I see the add requires modification for m38a1 What do I need to change to use this carb and is it the same height as my carter
Question By: Gavin on Oct 5 2017 6:25 PM
This carb will work for the A1 and you won't have any clearance issues. The main modification you will have to make is adding an air horn on top of the carb - 809785. Thanks!
Answer By: Willys Jeep Parts Tech on Oct 6 2017 5:00 AM
Questions: Do you have a rebuild kit for this solex carb?
Question By: Toby King on Aug 5 2017 4:55 PM
SK5 is the stock number.
Answer By: Willys Jeep Parts Tech on Aug 7 2017 5:56 AM
Questions: looking for the rod that when you push gas pedal hit the carbulator the back part conector.
Question By: Jose Ramos on Jul 8 2017 4:00 PM
Please email email@example.com or call us toll free and we can get more vehicle information.
Answer By: Willys Jeep Parts Tech on Jul 10 2017 6:03 AM
Questions: We have a 1938 Willy's Overland Crossley with a SOLEX carb...can't find anything on it but a C and an F stamped on opposite sides. If we sent a picture, might you be able to help us figure out model or part number?
Question By: firstname.lastname@example.org on Mar 12 2017 8:49 PM
Sure. Please email email@example.com and we can try to help out.
Answer By: Willys Jeep Parts Tech on Mar 13 2017 5:57 AM
Questions: Unlike the original carburetor on my M38A1, there isn't a "choke disk" that closes the air opening on the Solex to choke the engine at startup. After installing the Solex, the jeep is hard to start when cold. How does the Solex choke the carb.?
Question By: Kevin J on Dec 2 2016 5:10 PM
Its internal on the Solex. Make sure you are getting fuel flow to it if the engine has set up for while.
Answer By: Willys Jeep Parts Tech on Dec 5 2016 5:36 AM
Questions: After replacing my Carter 938 SD on my 1955 Willys Jeep CJ5 with the Solex carburetor, the hood will not close with the old oil bath air cleaner. What's the problem? I measured a height difference between the old carb and the new one at 3/4".
Question By: Chuck Davis on Sep 19 2016 6:58 PM
You have to use your original air horn with it. Something is unoriginal on your vehicle. This solex will 100% work to close the hood. Please call us toll free and we can help.
Answer By: Willys Jeep Parts Tech on Sep 19 2016 12:17 PM
Questions: The throttle stop broke, the piece that actually connects the linkage to the carb. Can I just get that? or a whole new carb? i modified the original carbs arm, but its not right.
Question By: Jesse on Sep 6 2016 1:33 AM
We can get you just that piece most likely. Please call us toll free.
Answer By: Willys Jeep Parts Tech on Sep 6 2016 6:08 AM
Questions: Do you sell an air filter that will fit this carb or do I have to use the oil bath filter system?
Question By: Jame Venturini on Jul 13 2016 3:26 PM
You have to use your original oil bath air cleaner on these.
Answer By: Willys Jeep parts Tech on Jul 13 2016 9:04 AM
Questions: Will this #923808 fit my 1966 cj5 jeep with dauntless v6 engine?
Question By: taylor on Dec 22 2014 12:00 AM
No, this is for the 4-134 F head engine only.
Answer By: Willys Tech on Dec 23 2014 12:00 AM
Questions: Where is the idle speed adjustment? The carb runs great, but the idle is too low. Please advise
Question By: Jay on Dec 3 2014 12:00 AM
There is a screw on the side. See link above as well for tuning.
Answer By: Willys Tech on Dec 3 2014 12:00 AM
Questions: Does solex make a carburetor for the hurricane 6. 161cu for f head?
Question By: Richard on Oct 23 2014 12:00 AM
No they do not. We can rebuild yours for the 6-161 engine. Please call us toll free.
Answer By: Willys Tech on Oct 24 2014 12:00 AM
Questions: Just recently purchased this carb and bolted it up. Ran very well and idled correctly but when I shut down the engine, within a minute or two the carb starts leaking fuel at the area where the choke cable hooks up, is there a solution to correct this or will I need to return the carb for replacement ?
Question By: MIke on Jan 1 1970 12:00 AM
Sounds like it may be flooding. I would double check your fuel pressure and if the motor is no shutting down properly i.e. chugging.
Answer By: Willys Tech on Sep 29 2014 12:00 AM
Questions: The Solex carb. for M38A1 with snorkel package What modification is necessary? Do you have one in stock? The probablem with my present carb is I think it is wore out I did rebuild but it must be running extremely rich and the plugs get all black shoot, enough shoot that it will go to missing and refuse to start unless you pull the plugs and clean every 10 miles
Question By: Mike on Sep 15 2014 12:00 AM
Yes we do have these in stock. You will also want to order part number: 809785
Answer By: Willys Tech on Sep 15 2014 12:00 AM
Questions: Do your Solex Carburetors come with the carburetor mount gaskets or do they need to purchased separately?
Question By: Mark on Aug 19 2014 12:00 AM
Yes they come with the base gasket.
Answer By: Willys Tech on Aug 20 2014 12:00 AM
Questions: i have a 1965 cj5 with a hurricane 4 motor when i start the motor it runs smooth then when i give it gas it cuts out real bad runs real ritch rebuilt carb didnt help still runs ruff do i need new carb
Question By: kelly on Jul 19 2014 12:00 AM
Could be alot of things. I would try to lean the idle screw, Advance your distributor a bit, and check your fuel pressure.
Answer By: Willys Tech on Jul 21 2014 12:00 AM
Questions: Have the rods connecting the accelerator pedal to the carburetor?
Question By: Luis on Apr 2 2014 12:00 AM
Please call us toll free. We can probabaly help you with the linkage.
Answer By: Willys Tech on Apr 3 2014 12:00 AM
Questions: My 53 M38A1 has a Carter YS-950. Do you have a Solex to replace that or is this it? I will still need Part #809785 ? Thanks.
Question By: Nick on Mar 17 2014 12:00 AM
This will replace it. Yes you will also need the air horn to clamp ontop to make the 90 degree bend.
Answer By: Willys Tech on Mar 18 2014 12:00 AM
Questions: If this carburator fix my 1970, 134 cc. Hurracaine ,In the picture look to be diferent to conect the chock cable
Question By: Jose on Mar 9 2014 12:00 AM
Yes, this is the proper replacement carb for the 4-134 F head engine.
Answer By: Willys Tech on Mar 10 2014 12:00 AM
Questions: I have to pour fuel into the carb to start when cold. Jeep also stumbles badly when cold. It seems as though the choke doesn't create enough rich mixture. The accelerator pump is working as I can see fuel come out the nozzle when the throttle opened but the engine will not start even after pumping throttle. I even put a electric pump on thinking the carb was draining after shutting off. Can the solex be adjusted to make it run more rich.
Question By: Rex on Dec 2 2013 12:00 AM
There is an adjustment screw at the base to change the mixture.
Answer By: Willys Tech on Dec 2 2013 12:00 AM
Questions: Have a 53 CJ-3B. Carb is a Carter YF 738 (not 938). Is this Solex a direct replacement?
Question By: David on Jan 1 1970 12:00 AM
They originally used a 938 on that vehicle. The carb you have on there now is unoriginal. This is a replacement for the original they used.
Answer By: Willys Tech on Nov 19 2013 12:00 AM
Questions: How tall is this carburetor? I have a 46 CJ2A with an F-134 engine, currently with a modified hood to allow the carb to fit, but I would like to restore the hood and fit it all underneath if possible. Thanks!
Question By: Sam on Nov 6 2013 12:00 AM
They are approx 6.5 like the carters.
Answer By: Willys Tech on Nov 6 2013 12:00 AM
Questions: Want to purchase the solex carburetor,I live at 10,000 foot elv. do I need a high altitude jet for cj3b?
Question By: Brian on Feb 8 2013 12:00 AM
You probably can adjust it for the elevation.
Answer By: Willys Tech on Feb 11 2013 12:00 AM
Questions: will the solex carburetor fit 1941 gpw ford jeep
Question By: dillon on Jan 21 2013 12:00 AM
They used a 4-134 L head engine on that vehicle. That is part number: 923806.
Answer By: Willys Tech on Jan 21 2013 12:00 AM
Questions: HAVE EARLY MODEL 50 SOMETHING FC 150 6VOLT 134 DO YOU HAVE A CARB FOR IT
Question By: ROBERT on Dec 4 2012 12:00 AM
For the FC-150 we can rebuild your carburetor for you. Please call us toll free.
Answer By: Willys Tech on Dec 4 2012 12:00 AM
Questions: I just bought an 1965 Kaiser. The problem is it wont idle without the choke fully closed. is the carb worn out??? I live in a warm climate, Houston
Question By: kevon on Jul 24 2012 12:00 AM
Its tough to say for sure. You should try adjusting your timing and check your fuel pressure if is rough idle. You may need a new carb.
Answer By: Willys Tech on Jul 24 2012 12:00 AM
Questions: what is the normal level of fuel in a fuel pump bowl on a f head cj
Question By: Anonymous on Jul 18 2012 12:00 AM
Fuel pump fill levels vary. Some fill up some remain low. The big thing is that your fuel pump only puts out 2-1/2 pounds pressure.
Answer By: Willys Tech on Jul 18 2012 12:00 AM
Questions: Can I get just the float for this carb? My float fills with gas and sinks.
Question By: Dan on Jun 27 2012 12:00 AM
I would do the water test on it. Place it in a glass of water and see where the bubbles are coming out. Sauder the hole.
Answer By: Willys Tech on Jun 29 2012 12:00 AM
Questions: Does this carburetor have any kind of filter built in it?
Question By: Tyler on Jun 11 2012 12:00 AM
If you have a rusty fuel tank I would also buy part number: 8126312
Answer By: Willys Tech on Jun 12 2012 12:00 AM
Questions: will your solex fit my m 151 a2
Question By: fernand on Apr 29 2012 12:00 AM
It should work ok with some modification of the linkage.
Answer By: Willys Tech on Apr 30 2012 12:00 AM
Questions: I need a complete carburetor model 1954 jeep Willys CJ-S
Question By: Market used auto sale on Jan 1 1970 12:00 AM
I think you mean CJ-5. They didnt start making those untill 1955 really. This is a direct replacement for the vehicles listed above with the 4-134 F head engine with the Carter YF carb.
Answer By: Willys Tech on Apr 19 2012 12:00 AM
Questions: I have a 55 CJ-5. Little rough around the edges, but getting cleaned up. The carb needs to be rebuilt. It looks like the #923995. It also has the original oil bath air filter. Will the Solex #923808 fit in its place? If so, will it need any other parts to make it work?
Question By: Brody on Apr 4 2012 12:00 AM
Yes this is a direct replacement for your Carter YF carburetor. All your linkage will go right on.
Answer By: Willys Tech on Apr 5 2012 12:00 AM
Questions: i have a 49 truck with 134 f moter do u have replacement carb
Question By: Anonymous on Dec 4 2011 12:00 AM
We have options. Please call us toll free.
Answer By: Willys Tech on Dec 5 2011 12:00 AM
Questions: if i was to replace my carter with the solex.. any adjustments needed at 3000 foot level for the solex for my 1962 cj-5 with f-134 motor
Question By: Anonymous on Nov 7 2011 12:00 AM
You should be ok with a simple idler air adjustment.
Answer By: Willys Tech on Nov 7 2011 12:00 AM
Questions: Will the replacement Solex Carburettor fit my 1967 Kaiser jeep CJ5?
Question By: Ian Moss on Oct 6 2011 12:00 AM
Yes as long as you have the 4-134 F head engine.
Answer By: Willys Tech on Oct 6 2011 12:00 AM
Questions: Have a CJ-2A, need carburetor replacement. My carburetor is a M34 PBIC and the S-number is CJ-2A 1281406
Question By: Emilio Leal on Sep 5 2011 12:00 AM
Originally they used a Carter WO carburetor. You would want to order part number: 923806 to replace it.
Answer By: Willys Tech on Sep 6 2011 12:00 AM
Questions: hello my cable trothle and choke is same fit?
Question By: Anonymous on Jul 30 2011 12:00 AM
Yes your old cables fit up just like orignal.
Answer By: Willys Tech on Aug 1 2011 12:00 AM
Questions: Does this come with the main gasket?
Question By: David on Apr 8 2011 12:00 AM
Yes, that is correct, it has the base gasket.
Answer By: Willys Tech on Apr 11 2011 12:00 AM
Questions: Is this a downdraft or sidedraft carburetor?
Question By: Dan on Feb 6 2011 12:00 AM
These are a downdraft.
Answer By: Willys Tech on Feb 7 2011 12:00 AM
Questions: What other part has to be ordered to fit an M38A1 and how much does it cost?
Question By: Jim on Jan 18 2011 12:00 AM
I would order part number: 809785 and you should be all set.
Answer By: Willys Tech on Jan 19 2011 12:00 AM
Questions: I have a 1965 cj5 with 134 f head engine with a carter nf carb. in need of rebuild, I either want to rebuild or buy new. I have heard solex replacement is a better carb. My question is solex exactly the same as nf for fuel line hookup & linkage, I want to mount carb & hookup original linkage, fuel line & everything else. Also is a better carb
Question By: Al on Jan 12 2011 12:00 AM
Yes, these are direct replacements for the original Carter Carburetors used on these vehicles. They are plug and play.
Answer By: Willys Tech on Jan 13 2011 12:00 AM