Questions & Answers
Questions: do you guys sell replacement universal joints for the axle shafts? I need one for the long shaft on my dana 27
Question By: Tyler on May 1 2022 6:22 PM
Answer By: Willys Jeep Parts Tech on May 2 2022 5:41 AM
Questions: I have a dana 27 for a 3B I'm rebuilding. I need replacement shafts for it. the shafts I pulled out are 10 spline. will this item work for the short shaft? and the long shaft you guys have for the dana 25, will it work for my 27?
Question By: Tyler on May 1 2022 6:15 PM
Yes that is right and 909459 for the other side.
Answer By: Willys Jeep Parts Tech on May 2 2022 5:44 AM
Questions: Could I get the specs, diameter, length...?
Question By: Superior Automotive Tech on Dec 3 2021 2:28 AM
Please email mike@Kaiserwillys.com what all specs your wanting and we can help.
Answer By: Willys Jeep Parts Tech on Dec 6 2021 5:53 AM
Questions: I have a 10 spline dana 25 right hand side. The inner axle shaft is 16 3/4” and the total length is 24 3/4”. Do you have something that would work for me?
Question By: Craig Ruschkowski on Feb 6 2021 8:20 PM
Please email email@example.com some more vehicle information and we can help out. Thanks!
Answer By: Willys Jeep Parts Tech on Feb 8 2021 5:29 AM
Questions: I need the weight of each front axle shaft, cause I need to buy from you, and then when it arrived to Miami I need to send the axles air way freight to South America, Uruguay, where is my CJ2A
Question By: Oscar Latorre on Jan 10 2020 12:28 PM
These weight approx 10 pounds boxed each.
Answer By: Willys Jeep Parts Tech on Jan 10 2020 5:34 AM
Questions: I bought some used axles to replace the ones in my 46 Willys. The splines are the a same and they go into the side gears fine. I removed the axle tube bushings but neither would go in far enough for the spindle to bolt up. I cut about 1/2 inch off the inner left axle and that fixed that issue. The right side it seems the splines are not cut deep enough. Is there a different inner axle length that I can buy
Question By: Ken on Oct 14 2019 7:56 PM
You may have a clearance issue there on the bushings at your housing or spindle. I would look at those. We do have NOS originals if you want to go that route too.
Answer By: Willys Jeep Parts Tech on Oct 14 2019 1:15 PM
Questions: I noticed that the u joint type axles do not have a machined area for the outer axle bushing to ride on. When replacing the repezza with a joint type shaft is it necessary to remove that brass sleeve from the axle tube?
Question By: Bruce Clow on Aug 6 2019 11:42 PM
If you are replacing the early style axles with these spicer style axle, you may have to take some off the bushing for clearance.
Answer By: Willys Jeep Parts Tech on Aug 7 2019 6:39 AM
Questions: I ordered these but the u-joint/yoke won't slide through knuckle hole on my 48 cj2a. The u-joint part is too big. Your video shows them sliding through the knuckle hole. Do I need to remove the steering knuckle to install these?
Question By: Eric on May 3 2019 10:01 PM
You could put in from backside if you slide it off. Send photos to Mike@kaiserwillys.com so we can take a look.
Answer By: Willys Jeep Parts Tech on May 6 2019 5:43 AM
Questions: What size universal joints are in these axles shafts? I don't need the shafts just need to replace a universal joint.
Question By: HAnk on Mar 3 2019 2:47 PM
8126614S is the part number for them.
Answer By: Willys Jeep Parts Tech on Mar 4 2019 5:37 AM
Questions: Are the rzeppa axleshafts for a dana 25 axle interchangeable with the spicer style axleshafts? In other words if I had an axle with one style could I replace them with the other style?
Question By: Paul Weiler on Dec 28 2018 10:33 PM
If you can email firstname.lastname@example.org more vehicle information and I can help out.
Answer By: Willys Jeep Parts Tech on Jan 2 2019 5:49 AM
Questions: Does the outer flange fit up? I have this shaft but my outer flange fits very tight.
Question By: Chris Bunten on Aug 30 2018 2:02 AM
Yes, your drive flange will slide onto the end of the shaft.
Answer By: Willys Jeep Parts Tech on Aug 30 2018 5:35 AM
Questions: I will be replacing my Rzeppa style axles with the Spicer type that you offer and I have two questions. One how does one install lockout hubs when there is a snap ring at the end of the axle, and if you leave the snap ring off will the end play in the axle be OK? Two, I see that the Spicer joint is pre-greasable before it is assembled, but how can it be greased again when it is in a closed knuckle application? Thank you.
Question By: Loren on Feb 24 2015 12:00 AM
Typically if you have the snap ring style axle shaft the length wont cause any problems. It just bolts up. The spicer style has a grease fitting that usually is just a one time grease.
Answer By: Willys Tech on Feb 24 2015 12:00 AM
Questions: when I removed the passenger side front axle from a 53 cj-3a the balls fell out of the joint. is this normal or is the joint worn out?
Question By: Dave Blasingame on Jan 5 2015 12:00 AM
Sounds like you have worn balls on the joint. If you still have all the parts you could put them back together but they probably need to be replaced.
Answer By: Willys Tech on Jan 6 2015 12:00 AM
Questions: Switching to these Axle Shaft will that eliminate the need to grease inside the front hub?
Question By: Anonymous on Aug 12 2014 12:00 AM
You would still want to grease it just to make sure it is all lubricated but yes this is a spicer style joint that can be pregreased.
Answer By: Willys Tech on Aug 12 2014 12:00 AM
Questions: I understand these replace the RZeppa but I don't see the threaded end that the RZeppa has. Is/are there additional parts needed?
Question By: Rick on Oct 22 2013 12:00 AM
It comes with a snap ring to convert you over. Only really early ones were threaded.
Answer By: Willys Tech on Oct 23 2013 12:00 AM
Questions: Are all '46 CJ-2A front axles Dana 25's ? Seems to me that when I did the rebuild (14 years ago) that mine was a Spicer 21 with a Bendex joint. Am I correct or fuzzy in the brain ?
Question By: Jim on Mar 29 2013 12:00 AM
Yes all CJ-2A's or any 4wd Willys thru 65 were Dana 25. Starting the the 60's some CJ-5's had a Dana 27 option.
Answer By: Willys Tech on Mar 29 2013 12:00 AM
Questions: Does anything have to be changed or adjusted when replacing the bendix style with this?
Question By: Anonymous on Nov 15 2012 12:00 AM
Sometimes you have to take out the bushing at the end of your axle housing tube for clearance. Other than that you are all set to slide in.
Answer By: Willys Tech on Nov 19 2012 12:00 AM
Questions: what is the overall complete lenth also mine has a splined nut at the end past the 10 splines
Question By: Anonymous on May 30 2012 12:00 AM
Answer By: Willys Tech on May 30 2012 12:00 AM
Questions: Am I correct in assuming these axles and Ujoints replace the original Bendix axles with the ball type joint?
Question By: Bob on Nov 22 2011 12:00 AM
Yes that is correct. They are direct replacements.
Answer By: Willys Tech on Nov 23 2011 12:00 AM
Questions: Am I correct to assume these are 10 spline axles?
Question By: Bob on Feb 3 2011 12:00 AM
Yes, that is correct.
Answer By: Willys Tech on Feb 3 2011 12:00 AM